Symbol Description : (use), (no use)
Standard Mode
Zone Output Mode
H Level Mode
L Level Mode
ONE short Mode
Double Deviation Mode
Output HH: Comparative HH
Displayed Value
Output H : Comparative H
Displayed Value
Output PASS: when output HH, H,
L, LL is OFF, it is ON
Output L : Comparative L
Displayed Value
Output LL : Comparative LL
Displayed Value
In the case of outputting when the SV is set and it is higher than HH deviation,
H deviation, L deviation, LL deviation from the SV
SV Auto Setting: The present displayed value is saved by pressing the front
+ keys
SV display: The saved SV is displayed SV by pressing key and if
by pressing key one more time then it will display the present value
Comparative HH
Comparative H
Comparative L
Comparative LL
Output HH
Output H
Output PASS
Output L
Output LL
Hys
Hys
Hys
Hys
Output HH: Comparative HH
Displayed Value
Output H : Comparative H
Displayed Value <
Comparative HH
Output PASS: when output HH, H,
L, LL is OFF, it is ON
Output L : Comparative L <
Displayed Value
Comparative LL
Output LL : Comparative LL
Displayed Value
LL
L H HH
Comparative HH
Comparative H
Comparative L
Comparative LL
Output HH
Output H
Output PASS
Output L
Output LL
Hys
Hys
Hys
Hys
Output HH: Comparative HH
Displayed Value
Output H : Comparative H
Displayed Value
Output PASS: when output HH, H,
L, LL is OFF, it is ON
Output L : Comparative LL
Displayed Value
Output LL : Comparative LL
Displayed Value
LL
L H HH
Comparative HH
Comparative H
Comparative L
Comparative LL
Output HH
Output H
Output PASS
Output L
Output LL
Hys
Hys
Hys
Hys
Output HH: Comparative HH
Displayed Value
Output H : Comparative H
Displayed Value
Output PASS: when output HH, H, L,
LL is OFF, it is ON
Output L : Comparative LL
Displayed Value
Output LL : Comparative LL
Displayed Value
Comparative HH
Comparative H
Comparative L
Comparative LL
Output HH
Output H
Output PASS
Output L
Output LL
Hys
Hys
Hys
Hys
Output HH: Comparative HH
Displayed Value
Output H : Comparative H
Displayed Value <
Comparative HH
Output L : Comparative LL <
Displayed Value
Comparative L
Output LL : Comparative LL
Displayed Value
Comparative HH
Comparative H
Comparative L
Comparative LL
Output HH
Output H
Output PASS
Output L
Output LL
0.3s
0.3s
0.3s
0.3s
Deviation Setting Range:
0.0001 ~ 99999
SV : Setting Value
PV : Displayed Value
HH Deviation
H Deviation
SV
L Deviation
LL Deviation
H Deviation Output
HH Deviation Output
PV
L Deviation Output
LL Deviation Output
Starting Compensation Timer Function
After turning the power ON, as invalidating the measurement in the some
periods of time, the function limits the faulty output caused by the faulty
value which is affected by the chattering or inputting the starting current or
etc. irregularly.
Specially, when starting the revolving object, it validates in the case
that it does not make the comparative (L, LL) judgment by the low
speed revolution operation.
The setting time of the
starting compensation
from 0.1 sec. to
99.9 sec.
Parameter Group Flow Chart
SP Group (Comparative Setting Group)
Menu Setting Flow Chart
Key Description
Hysteresis Function
In the case of the measured value becomes unstable around the
comparative value, set the hysteresis value from the setting value in
order to prevent the unstable operation in the output.
For the comparative value HH, H, the decreased value is applied as the
hysteresis value and for the comparative value LL, L, the increased
value is applied as the hysteresis value.(The default setting is 1 and 0
can not be set.)
Notice 1) : Press for 2 sec. to enter and release key to enter Peak Group
Note 6) the display only product, BP6-5AN and the non-main output product, BP6-5A6, are not displayed like the above parameter comparative setting
group. If each parameter is set and the hysteresis value is inputted, you can stably obtain the desired output.
Peak Hold or Reset Function
This function displays MAX value and MIN value in the comparative values. It is
possible to select a function by the one-touch button.
Peak Hold Setting
Peak Hold Save & Confirmation
MAX Peak Value : save the value
MIN Peak Value : save the value
Display Cycle Setting Function
This is the function which can change the cycle about the display cycle
of the displayed value so that it displays in the time unit of the set cycle.
Setting Display Cycle = 0.05/0.5/1/2/4/8 sec.
Time Unit Selection Function
As selecting the measurement value in the various time units, the
function displays the values efficiently.
The time unit function can display after selecting one between the
decimal system and sexagesimal system.
The time unit is applied only for F3, F4, F5, F6 mode
Display Value: 00000
Setting
time
Comparative L(LL)
Power ON
L(LL) Output
Comparative HH, H
Output HH, H
Comparative L, LL
Output L, LL
Hysteresis (0<Hys)
Hysteresis (0<Hys)
Auto Zero Time
The function is that if there is no input value in the time which is set as
Auto Zero Value, then the displayed value will be
00000 by
compulsion. In the case of there is no pulse input in a period of time or
the predicting setting when the stop of the revolving object will be
occurred, it can be set and used the time as the setting time of Auto Zero.
The setting time of Auto Zero is from 0.1 sec. to 9999.9 sec.
Setting Menu
Meaning Setting Contents
Default
Comparative Setting
Group Selection
Comparative HH Setting
Comparative H Setting
Set Value(Only Out-d)
Comparative L Setting
Comparative LL Setting
F1, F2, F7, F8, F9 : 0 ~ 99999
F3, F4, F5, F6 : 0 ~ set time range
If set a measuring value under a decimal point, below set value
can be convert to be set under decimal point
Display
Peak Value Save
Comparative Value Save
Prescale Time Set
IN/OUT Set Option Set
2 s
2 s
2 s 2 s 2 s
2 s
Menu
Notice 1)
Notice 2)
Notice 2) : If you press for 3 sec, You can enter Menu.
(note 3)
(note 4)
(note 5)
(note 5)
Parameter Table For Each Operation Mode
Output Mode Function Description
Parameter Description
Default Value of Parameter
Initial Initial
Initial Initial
Displayed
Characters
F1 F2 F3 F4 F5 F6 F7 F8 F9
SP Group (Comparative Value Setting Group)
PS Group (Prescale or Time Option Setting Group)
Setup Group (IN / OUT Setting Group)
Option Group (Option Setting Group)
Peak Display Group (Peak Value Save Group)
The communication setting is a system operation which is not
related with the modes
The remote control is a system operation which is not related with the modes
To Next Page
Loading...
Need help?
General
