Harbor Breeze 1060138

Questions and Answers

R
Rebecca MartinezAug 9, 2025
Why is my Harbor Breeze 1060138 Fan remote control not working?
- E
  Erika DavilaAug 9, 2025
  The Harbor Breeze Fan remote control might not be working due to several reasons. First, a power surge may have cleared its memory, requiring re-syncing: turn the fan power off and on, then within 30 seconds, press and hold the HIGH SPEED and LOW SPEED buttons (or the “LEARN” button in the battery compartment) for 5 seconds until the fan turns on at low speed and the light turns off. This confirms successful syncing. Second, the battery may need replacing; insert new CR2032 batteries. Third, interference from another remote could be the issue; try turning off other nearby fans and re-syncing the remote.
H
hernandezrachelAug 15, 2025
How to fix excessive wobbling in my Harbor Breeze 1060138 Fan?
- D
  David SmithAug 15, 2025
  Excessive wobbling in your Harbor Breeze Fan can be due to several factors. First, check and tighten all screws that hold the fan blades to the blade arms and the blade arms to the motor. Second, the blades might be unbalanced; try switching one blade with a blade from the opposite side or use a blade balancing kit. Third, ensure the fan mounting is secure by turning off the power, loosening the canopy, and verifying the mounting bracket is flush and secure to the electrical outlet box. Fourth, if the fan is too close to a vaulted ceiling, use a longer downrod or move the fan. Finally, check and tighten the set screw on the motor housing yoke.
J
Jill WilliamsAug 21, 2025
What to do if my Harbor Breeze 1060138 Fan does not move?
- Z
  zayalaAug 21, 2025
  If your Harbor Breeze Fan isn't moving, check the following: Ensure the power is on and the fuse is not blown. Turn the power off, loosen the canopy, and check all wire connections. Verify that the connectors from the light kit fitter and fan are properly connected. Also, make sure the reverse switch is fully engaged to the left or right.
R
Robert LeeAug 27, 2025
How to fix lights not working on Harbor Breeze 1060138 Fan?
- R
  Robert BaileyAug 27, 2025
  If the fan is working but the lights aren't, ensure that the 6-pin connectors from the light kit are properly connected. If that doesn't solve the problem, turn off the power and check all connections at the ceiling outlet box.
M
Mr. Mark SuarezSep 2, 2025
Why is my Harbor Breeze 1060138 so noisy?
- B
  Brittany CopelandSep 3, 2025
  A noisy Harbor Breeze Fan can be attributed to several causes. Ensure all screws that hold the fan blades to the blade arms and the motor are tightened. A cracked blade can also cause noise, so replace it if necessary. Avoid using a full range dimmer switch, as it is not compatible with the fan. Also, make sure the outlet box is securely attached to the building structure and that the mounting bracket is securely attached to the outlet box with tight screws.

Summary

Safety Information

General Safety & Electrical Precautions

Covers power disconnection, clearance, dimmer switch use, wire connector limits, and using provided parts.

Mounting & Outlet Box Safety

Addresses outlet box security, support requirements, and proper mounting bracket installation.

Standard or Angle Mounting Instructions

Wiring

Connecting Household and Fan Wires

Provides steps for connecting green, white, and black wires using wire connectors.

Securing and Routing Wires

Instructs on wrapping wire connectors with tape and pushing wires into the outlet box.

This document is a user manual for the Flanagan II Ceiling Fan, models #42477, #42478, and #42483, manufactured by Harbor Breeze. It provides detailed instructions for assembly, installation, operation, maintenance, and troubleshooting, along with safety information and a parts list.

Function Description:

The Flanagan II Ceiling Fan is designed to provide air circulation and lighting in residential spaces. It features multiple fan speeds, a light kit with adjustable color temperature, and a remote control for convenient operation. The fan can be mounted in standard or angled/vaulted ceiling configurations. It also includes a reverse switch to change airflow direction for different seasons, creating a wind chill effect in warmer weather and helping to circulate warm air in cooler weather. Special features like "Light Delay" and "Home Shield™" enhance its utility.

Important Technical Specifications:

Models: #42477, #42478, #1060138
Net Weight: 15.67 lb (7.11 kg)
Minimum Clearance (Blades to Floor): 7 ft
Minimum Clearance (Blades to Obstruction): 30 in.
Ceiling Angle (for Angle Mounting): Not steeper than 16°
Outlet Box Support: Must be marked "ACCEPTABLE FOR FAN SUPPORT" and capable of supporting at least 35 lbs.
Wire Connectors: Designed to accept one 12-gauge house wire and two fan lead wires.
Total Fixture Wattage: 22.5 watts (LED, not replaceable)
Remote Control Battery: CR2032 lithium batteries (DC3V)
Light Color Temperature: Adjustable from 2200K (warm white) to 6500K (daylight)
FCC Compliance: Part 15 compliant, subject to two conditions: (1) device may not cause harmful interference, and (2) device must accept any interference received.

Usage Features:

Remote Control Operation: The fan is operated via a remote control with dedicated buttons for:
- Fan Off: Turns the fan power off.
- Light Control: Taps to turn light on/off; press and hold to dim/brighten and change color temperature (2200K-6500K).
- High Speed: Turns fan on at high speed.
- Light Delay: Keeps light on for 60 seconds for safe exit; blinks once to confirm activation; press any button to cancel.
- Medium Speed: Turns fan on at medium speed.
- Variable Breeze: Simulates a natural breeze; press and hold to activate; press any fan speed button to cancel.
- Low Speed: Turns fan on at low speed.
- Home Shield™: Simulates occupancy by randomly turning the light on/off (5-20 minutes on, 60 minutes off between events); press and hold to activate; light blinks twice to confirm; press any button to cancel.
Reverse Switch: Located on the motor assembly, it allows changing the blade rotation direction.
- Warmer Weather (Sun Icon): Push switch left for downward airflow, creating a wind chill effect.
- Cooler Weather (Snowflake Icon): Push switch right for upward airflow, helping to move hot air off the ceiling.
- Important: Fan must be stopped before moving the reverse switch. The switch must be fully engaged left or right for proper operation.
LEARN Button: Used to sync the remote control with the fan's receiver. Accessible by removing the battery door on the remote.
Mounting Options:
- Standard Mounting: Suitable for ceilings 8 ft. or higher.
- Angle Mounting: Suitable for angled or vaulted ceilings (up to 16°). A longer downrod may be needed for proper blade clearance.
- Flushmount/Closemount: Not available for this specific model.

Maintenance Features:

Regular Inspection: At least twice a year, lower the canopy to check and tighten all screws on the downrod assembly and fan.
Cleaning:
- Motor Housing: Clean with a soft brush or lint-free cloth to avoid scratching the finish.
- Blades: Clean with a lint-free cloth.
- Important: Do not use water or a damp cloth to clean the ceiling fan.
Battery Replacement: Replace remote control batteries with CR2032 lithium batteries when the LED indicator does not illuminate. Exhausted batteries should be removed, and non-rechargeable batteries should not be recharged. Do not dispose of batteries in fire.
LED Light Kit: The LED light kit is not designed to be replaced by the user. Total fixture wattage is 22.5 watts.
Troubleshooting Guide: The manual includes a comprehensive troubleshooting section to address common issues such as the fan not moving, excessive noise, wobbling, lights not working, and remote control malfunction. This includes steps for checking power, wiring connections, blade balance, and re-syncing the remote.
Limited Lifetime Warranty: The manufacturer warrants the fan to be free from defects in workmanship and materials for a lifetime (original purchaser). Other fan parts (excluding glass/plastic blades) are warranted for one year. Warranty service requires proof of purchase. Damage from accident, misuse, improper installation, or unauthorized service voids the warranty. Natural changes in brass finish (rusting, pitting, corroding, tarnishing, peeling) are not covered. A small amount of "wobble" is considered normal.