Harman Kardon AVR20 II

1. INFRARED TRANSMITTER
WINDOW
The infrared beam is emitted forward
from this window when you press any
button on the commander. For the
remote controls to function properly,
always face this window toward the
remote sensor window on the receiver
and do not obstruct this window with
any material.
2. POWER BUTTON
Press this button to turn the power on
and off. - Automatic power on: When you
press the input function buttons (CD,
TUNER, TAPE 1, TAPE 2,
TV/AUX, VCR 1, VCR 2, PHONO) in
STANDBY mode, the power is
automatically turned on and the function
is selected.
3. TUNING UP/DOWN
Press these buttons to tune the
receiver up or down.
_
4,
PRESET
SCAN
BUTTON
|
Button
for
scanning
preset
station
—
frequencies
(see
page
15).
9. NUMERIC BUTTONS
These buttons can be used for preset
tuning in TUNER mode. Preset tuning:
Press the TUNER button to change the
input function of the receiver to TUNER
and then select one of 30 preset
locations.
6. CD FUNCTION BUTTONS
For a CD PLAYER: DISC (DISC
SELECTOR, this is available for the
Harman Kardon FL8400 CD changer),
(play), (pause), (stop), (backward
search), (forward search), (backward
skip), (forward skip), A-B and INTRO
buttons are available. - When selecting
a disc, press the DISC button. A-B
button is used to repeat a specific
passage.
7. CASSETTE DECK
FUNCTION
BUTTONS - For a cassette deck:
(pause), (stop), (record), (reverse play),
(forward play), (rewind), (fast forward)
buttons are available.
8 DELAY TIME BUTTON
This button operates only in DOLBY
PRO-LOGIC and HALL mode. In
these modes, the output signal from
the surround speakers is delayed
slightly from that of the front speakers.
Select appropriate delay time to
achieve the best surround sound effect.
For Dolby-Surround sound, we
recommend a 20ms delay. The time is
changed as below, when the button is
pressed in succession.
DOLBY PRO-LOGIC MODE
i 15 ms +20 ms — 25 ohne
HALLMODE
- ms — 10ms—15 ms 20 ms — 25 ms — 30 =|
9. INPUT FUNCTION
SELECTOR
Press the button to select the desired input
function. The available buttons are CD,
TUNER, TAPE 1, TAPE 2, TV/AUX, VCR
1, VCR 2, and PHONO:
10. CENTER LEVEL
UP/DOWN BUTTONS
Use these buttons to adjust the sound
level of the center speaker to that of the
front speakers. These buttons work only
in DOLBY PRO-LOGIC and DOLBY 3
STEREO mode. These buttons do not
work in PHANTOM.
11. CENTER MODE BUTTON
Selects the center mode (see page 14).
12. TEST TONE BUTTON
Generates test sounds in all channels
(Left, Center, Right and Surround) in
succession.
AVR20 II System Remote Control
13. REAR LEVEL
UP/DOWN BUTTONS
These buttons operate only in DOLBY
PRO-LOGIC and HALL mode. Use these
buttons to adjust the sound level of the
surround speakers. Set the MASTER
VOLUME control at the desired level
and press the up or down button until
you get the optimum surround effect at
your listening position.
14. MASTER VOLUME
BUTTONS
Adjust the overall (front, center, and
rear) volume level.
15. DISPLAY BUTTON
Press once and the display dims, press
again and it turns off. Press a third
time and it goes on.
16. SLEEP BUTTON
Sets the receiver to automatically turn
off after 10, 20, 30, 60, or 90 minutes.
Each time the button is pressed, the
setting is advanced as below.
" Omin —> 20min ~~30min 60min —»90min —» OFF 7
The display will dim when the sleep
function has been set
16