Harman Accentra 52i - Automatic Ignition Operation

Harman® • Accentra 52i Owner’s Manual_R8 • 2013 -___ • 07/1413 3-90-00574c
Igniter Switch to "AUTO" (up position)
Make sure the unit is plugged into a properly grounded, 120
VAC, 60 Hz electrical source. The power light should be the
only light lit.
Note: Be sure there is no fuel or other combustibles in
the ash pan prior to lighting.
1. Turn Mode Selector to "OFF".
2. Fill hopper with pellets.
3. Clean burn pot with scraper, if necessary.
4. If starting after an empty hopper, turn Feed Adjuster to
"TEST" (for one 60 second cycle). This will ow pellets
into the auger tube and also allow you to check the motors
for operation.
NOTE: The auger motor will not operate with the view
door open.
5. Turn Feed Adjuster to #4.
6. Flip the Igniter Switch up into the "AUTO" position.
7. Turn the Temperature Dial to the desired room temperature.
8. Turn Mode Selector to Room Temperature or Stove
Temperature.
9. Fill hopper with pellets and remove ashes as required.
Keep the hopper lid and rebox doors closed while in
operation. Failure to do so will affect operation of the
appliance and may permit escape of smoke or gases into
the living space.
1. Fines are small pieces of broken pellets (sawdust). Fines do
notoweasilyandoftenbuilduponthehopperfunnelbottom
angles.Thesenescanbepushedintothefeederopeningand
thenllthehopperwithpellets.Asthesystemworks,theywill
be burned.
2. The "TEST" cycle will operate the feed motor for exactly one
minute. Turning to "TEST" again and again may load too much
fuel into the burn pot causing excessive smoke on start-up.
3. Thereboxlowpressureswitchwillnotallowtheaugermotor
or the igniter element to operate if the view door is open.
4. Adjust Feed Rate. If this is your rst re or you are trying
different pellets, set the feed adjuster to #4, Figure 4.6 This is
a conservative number and will probably need to be increased.
After you know a feed rate setting that works well, use that
setting. Remember, if your feed rate is too high you may waste
fuel.
5. This is usually a weekly maintenance procedure. Cleaning the
burn pot with the scraper with a small amount of new fuel in the
bottom is not a problem. First, scrape the ashes off the front of
the burn pot into the ash pan. Then scrape the holed surface
downward into the burn pot. When the stove feeds, these
scrapings will be pushed out by the feeder.
6. The ash pan can hold the ashes from approximately 10 bags of
premium fuel.
7. Setting the feed adjuster # for maximum burn: With the unit
burning in"AUTO",turn to "Stove Mode" and put thefanon
"H".SettheTemperatureDialto#7.Allowtheunittoburnfor
about 30 minutes and check ash on front of burn pot. Figure 4.7.
If the ash line is larger than 1", turn the feed adjuster from #4
to #5. Allow another 30 minutes of burn time and check again.
If, at #6 setting, a 1" or less ash bed is not obtainable, it is not
a problem. The 1" ash bed is only at maximum burn rate and
during normal operation, the ash bed will be larger.
Figure 4.6
SeeNote7
1"
Figure 4.7
E. Automatic Ignition
BURNING GARBAGE, USE OF IMPROPER FUELS,
FIRE STARTERS OR ALTERING THE STOVE FOR
HIGHER HEAT OUTPUT MAY CAUSE DAMAGE TO THE
STOVE AND COULD RESULT IN A HOUSE FIRE. USE
ONLY APPROVED FUELS AND FOLLOW ONLY THESE
OPERATION GUIDELINES.
WARNING
!
NEVER USE GASOLINE, GASOLINE-TYPE LANTERN
FUEL, KEROSENE, CHARCOAL LIGHTER FLUID, OR
SIMILAR LIQUIDS TO START OR 'FRESHEN UP' A FIRE
IN THIS HEATER. KEEP ALL SUCH LIQUIDS WELL
AWAY FROM THE HEATER, WHILE IN USE.
WARNING
!