Harman Accentra 52i - Manual Ignition Operation

Harman® • Accentra 52i Owner’s Manual_R8 • 2013 -___ • 07/1415 3-90-00574c
Igniter Switch to “MANUAL” (down position) Make
sure the unit is plugged into a 120 VAC, 60 Hz electrical
source. The power light should be the only light lit.
NOTE: Be sure there is no fuel or other combustibles in
the ash pan prior to lighting.
1. Turn FEED ADJUSTER to desired feed rate. No. 4 is good
for most pellets.
2. Turn the MODE SELECTOR to “OFF” and then to
the desired mode. This will reset control and start the
combustion motor.
3. Turn the TEMPERATURE DIAL to the desired setting.
4. Clean burn pot with scraper if necessary.
5. Fill burn pot with pellets, only level with front edge. (Do
Not Over Fill).
6. Add starting gel on top of the pellets. Stir gel into pellets
for fast lighting.
7. Light starting gel with a match, and close the door.
Operation will begin when the re reaches the proper
temperature.
8. Fill hopper with pellets and remove ashes as required.
Store fuel in a dry area, away from all ignition sources and
outside all limits of the stove's clearance requirements to
combustibles. Do not store the fuel were it interferes with
the refueling of the stove or emptying of ashes. Do not store
any ashes removed from the stove near the fuel or other
combustible materials.
STARTER
GEL
1. Fines are small pieces of broken pellets (sawdust). Fines do
notoweasilyandoftenbuilduponthehopperfunnelbottom
angles.Thesenescanbepushedintothefeederopeningand
thenllthehopperwithpellets.Asthesystemworks,theywill
be burned.
2. The "TEST" cycle will operate the feeder motor for exactly one
minute. Turning to "TEST" again and again may load too much
fuel into the burn pot causing excessive smoke on start-up.
3. The low pressure switch will not allow the feed motor to operate
if the viewing door is open.
4. Adjust Feed Rate. If this is your rst re or you are trying
different pellets, set the feed adjuster to #4, Figure 4.8. This is
a conservative number and will probably need to be increased.
After you know a feed rate setting that works well, use that
setting. Remember, if your feed rate is too high you may waste
fuel.
5. Settingthefeedadjuster#formaximumburn: With the unit
burningin"AUTO",turnto"StoveMode"andputthefanon"H".
SettheTemperatureDialto#7.Allowtheunittoburnforabout
30 minutes and check ash on front of burn pot. Figure 4.9. If
the ash line is larger than 1", turn the feed adjuster from #4 to
#5. Allow another 30 minutes of burn time and check again. If
, at #6 setting, a 1" or less ash bed is not obtainable, it is not
a problem. The 1" ash bed is only at maximum burn rate and
during normal operation, the ash bed will be larger.
F. Manual Ignition
Figure 4.8
Figure 4.9
NEVER USE GASOLINE, GASOLINE-TYPE LANTERN
FUEL, KEROSENE, CHARCOAL LIGHTER FLUID, OR
SIMILAR LIQUIDS TO START OR 'FRESHEN UP' A FIRE
IN THIS HEATER. KEEP ALL SUCH LIQUIDS WELL
AWAY FROM THE HEATER WHILE IN USE.
WARNING
!
BURNING GARBAGE, USE OF IMPROPER FUELS,
FIRE STARTERS OR ALTERING THE STOVE FOR
HIGHER HEAT OUTPUT MAY CAUSE DAMAGE TO THE
STOVE AND COULD RESULT IN A HOUSE FIRE. USE
ONLY APPROVED FUELS AND FOLLOW ONLY THESE
OPERATION GUIDELINES.
WARNING
!
SeeNote7
1"