Harris P7300 - P7300 Display and Status Information; Display Icons; Status Messages; Radio Operation Modes

P7300
Display & Status Icons
Radio is transmitting.
Radio is transmitting/receiving a call, call is queued.
T99 Mode is enabled.
Channel Guard (CG) enabled.
EDACS trunked system is in Failsoft™ mode.
Selected group/channel set at low power TX.
If icon is not visible, TX at high power.
Steady - Radio is transmitting or receiving a manual or OTAR
(Network) encrypted call.
Selected talk group/channel is operating in P25, Digital, or
Conventional mode.
Animated (rotating clockwise) – SCAN mode enabled.
Selected talk group/channel is a Priority 1, 2, or “in the scan
list.” The talk group or channel isn’t in the scan list if a priority
icon isn’t associated with it.
Special call select/entry mode (Individual or Telephone
Interconnect).
Gauges approximate battery voltage level. “Empty” indicates
low battery.
FLORIDA
NEW
YORK
VIRGINIA
BRAZIL
UNITED
KINGDOM
UAE
SINGAPORE
P7300 Radio Status Messages
CC SCAN
Control Channel Scan mode - Trunked mode
only.
Control channel lost, searching for a control
channel.
WA SCAN
Wide Area Scan mode - Trunked mode only.
Radio searching for a new system.
TALKARND
Talkaround mode - Conventional mode only.
Radio operating unit-to-unit.
SYSC ON
System Scan Features On - Trunked mode only.
SYSC OFF
System Scan Features Off - Trunked mode only.
LOW BATT
Low Battery - Battery charge too low to transmit.
RXEMER
Receive Emergency - Trunked mode only.
Indicates an emergency call is being received.
This message will be flashing on line two.
TXEMER
Transmit Emergency - Trunked mode only.
Indicates an emergency call has been
transmitted on this radio. This message will be
flashing on line two.
WHC
Who Has Called - Trunked mode only. Missed
Individual call.
UNKNOWN
Unknown ID - Trunked mode only. Individual call
being received from an unknown ID.
QUEUED
Call Queued - Trunked mode only. Indicates the
system has placed the call in a request queue.
SYS BUSY
System Busy - Trunked mode only. System is
busy, no channels available, queue is full, or
individual call being made to radi
o already
receiving a call.
DENIED
Call Denied - Trunked mode only. Radio or group
not authorized on selected system or group.
NOTICE!
The material contained herein is subject to U.S. export approval. No export or re-
export is
permitted without written approval from the U.S. Government. Rated: EAR99
; in accordance
with U.S. Dept. of Commence regulations 15CFR774, Export Administration Regulations.
Menu
The menu
key allows access to features that are not
available from the keypad.
1. Press the
key to enter menu mode.
2. Use the
or button
to scroll through the available
menu items.
3. Press the
key again to select the item.
4.
Depending upon the item selected, further scrolling using
the or button may be required.
5. Press the
key again to return to the active display.
Trunked Mode
Transmitting a Group Call
1. Select the group.
2. Press the PTT button and speak
normally while holding the
microphone approximately 2 (two) inches from your mouth.
3. Release the PTT button when finished speaking
and wait for
a reply.
Receiving a Group Call
1. Listen to the call.
2. The Group name or “GRxxxx” appears
in the display to
indicate a call is being received.
3. Press the PTT button and speak
normally while holding the
microphone approximately 2 (two) inches from your mouth.
4. Release the PTT button when finished speaking
and wait
for a reply.
Trunked Mode (cont’d)
Transmitting an Individual Call (P7370 Model)
1. Press the button to access individual call list.
appears.
2. Use the
or
button to scroll through the individual
call list or enter the Logical ID (LID) number from keypad.
3. Press the PTT button and speak
normally while holding the
microphone approximately 2 (two) inches from your mouth.
4. Release the PTT button when finished speaking
and wait for
a reply.
Receiving an Individual Call (P7370 Model)
1. Receive audio sounds when a call is received and
the
display reads: ID xxxxx
*INDV*
2. Press and hold the PTT button to respond. Radio continues
to ring until PTT is pressed or originating radio disconnects.
3. If call is cleared with no response, the radio stores
the ID in
Who Has Called (WHC) list and display: *WHC*.
4. Press the
key to display ID.
Press PTT button to
return call or press Monitor/Clear button to clear *WHC*.
Transmitting a Telephone Interconnect Call (P7370 Model)
1. Press the button to access phone call list. appears.
2.
Follow steps 2 through 4 in “Transmitting an Individual Call”
above.
Receiving a Telephone Interconnect Call (P7370 Model)
1. Receive audio sounds when call is received and the
display
reads: *PHONE*.
2. Follow Steps 2 through 4 for “Receiving an Individual Call.”
Conventional Mode
Transmitting a Call
1. Select the conventional system and channel.
2. Press the Monitor/Clear button briefly. If audio is heard or
is illuminated, then the channel is busy.
3. When the channel becomes available, press the
PTT button
and speak
normally while holding the microphone
approximately 2 (two) inches from your mouth.
4. Release the PTT button when finished speaking
and wait for
a reply.
Receiving a Call
1.
Select a conventional system and channel or turn Scan on
and make sure desired channel is in Scan list.
2. When the radio receives a call,
the radio unmutes and the
channel name or number appears in the display.
Declaring an Emergency
1. Press and hold the red Emergency/Home button.
2. and are illuminated in the display and *TXEMER*
flashes in the display. After 2-3 seconds, turns off.
3. *TXEMER* and
remain illuminated in the display until the
emergency is cleared.
4. Press the PTT button and
reappears. Speak normally.
5.
Release the PTT button when transmission is complete.
Press and hold the Clear/Monitor button,
then
simultaneously press the emergency button to clear an
emergency (if enabled through programming).
For more detailed operating i
nformation and a list of options
and accessories, refer to the Operator’s Manual
(MM-013994-001 - available online at www.pspc.harris.com).
P7300 Display & Status Icons
Radio is transmitting.
Radio is transmitting/receiving a call, call is queued.
T99 Mode is enabled.
Channel Guard (CG) enabled.
EDACS trunked system is in Failsoft mode.
Selected group/channel set at low power TX.
If icon is not visible, TX at high power.
Steady - Radio is transmitting or receiving a manual or OTAR
(Network) encrypted call.
Selected talk group/channel is operating in P25, Digital, or
Conventional mode.
Animated (rotating clockwise) – SCAN mode enabled.
Selected talk group/channel is a Priority 1, 2, or “in the scan
list.” The talk group or channel isn’t in the scan list if a priority
icon isn’t associated with it.
Special call select/entry mode (Individual or Telephone
Interconnect).
Gauges approximate battery voltage level. “Empty” indicates
low battery.
FLORIDA
NEW
YORK
VIRGINIA
BRAZIL
UNITED
KINGDOM
UAE
SINGAPORE
P7300 Radio Status Messages
CC SCAN
Control Channel Scan mode - Trunked mode
only. Control channel lost, se
arching for a control
channel.
WA SCAN
Wide Area Scan mode - Trunked mode only.
Radio searching for a new system.
TALKARND
Talkaround mode - Conventional mode only.
Radio operating unit-to-unit.
SYSC ON
System Scan Features On - Trunked mode only.
SYSC OFF
System Scan Features Off - Trunked mode only.
LOW BATT
Low Battery - Battery charge too low to transmit.
RXEMER
Receive Emergency - Trunked mode only.
Indicates an emergency call is being received.
This message will be flashing on line two.
TXEMER
Transmit Emergency - Trunked mode only.
Indicates an emergency call has been
transmitted on this radio. This message will be
flashing on line two.
WHC
Who Has Called - Trunked mode only. Missed
Individual call.
UNKNOWN
Unknown ID - Trunked mode only. Individual call
being received from an unknown ID.
QUEUED
Call Queued - Trunked mode only. Indicates the
system has placed the call in a request queue.
SYS BUSY
System Busy - Trunked mode only. System is
busy, no channels available, queue is full, or
indi
vidual call being made to radio already
receiving a call.
DENIED
Call Denied - Trunked mode only. Radio or group
not authorized on selected system or group.
NOTICE!
The material contained herein is subject to U.S. export approval. No export or re-export
is
permitted without written approval from the U.S. Government. Rated: EAR99
; in accordance
with U.S. Dept. of Commence regulations 15CFR774, Export Administration Regulations.
Menu
The menu
key allows access to features that are not
available from the keypad.
1. Press the
key to enter menu mode.
2. Use the
or button
to scroll through the available
menu items.
3. Press the
key again to select the item.
4.
Depending upon the item selected, further scrolling using
the or button may be required.
5. Press the
key again to return to the active display.
Trunked Mode
Transmitting a Group Call
1. Select the group.
2. Press the PTT button and speak
normally while holding the
microphone approximately 2 (two) inches from your mouth.
3. Release the PTT button when finished speaking
and wait for
a reply.
Receiving a Group Call
1. Listen to the call.
2. The Group name or “GRxxxx” appears
in the display to
indicate a call is being received.
3. Press the PTT button and speak
normally while holding the
microphone approximately 2 (two) inches from your mouth.
4. Release the PTT button when finished speaking
and wait
for a reply.
Trunked Mode (cont’d)
Transmitting an Individual Call (P7370 Model)
1. Press the button to access individual call list.
appears.
2. Use the
or
button to scroll through the individual
call list or enter the Logical ID (LID) number from keypad.
3. Press the PTT button and speak normall
y while holding the
microphone approximately 2 (two) inches from your mouth.
4. Release the PTT button when finished speaking
and wait for
a reply.
Receiving an Individual Call (P7370 Model)
1. Receive audio sounds when a call is received and
the
display reads: ID xxxxx
*INDV*
2. Press and hold the PTT button to respond. Radio continues
to ring until PTT is pressed or originating radio disconnects.
3. If call is cleared with no response, the radio stores
the ID in
Who Has Called (WHC) list and display: *WHC*.
4. Press the
key to display ID.
Press PTT button to
return call or press Monitor/Clear button to clear *WHC*.
Transmitting a Telephone Interconnect Call (P7370 Model)
1. Press the button to access phone call list. appears.
2. Follow S
teps 2 through 4 in “Transmitting an Individual Call”
above.
Receiving a Telephone Interconnect Call (P7370 Model)
1. Receive audio sounds when call is received and the
display
reads: *PHONE*.
2. Follow Steps 2 through 4 for “Receiving an Individual Call.”
Conventional Mode
Transmitting a Call
1. Select the conventional system and channel.
2. Press the Monitor/Clear button briefly. If audio is heard or
is illuminated, then the channel is busy.
3. When the channel becomes available, press the
PTT button
and speak normally while hold
ing the microphone
approximately 2 (two) inches from your mouth.
4. Release the PTT button when finished speaking
and wait for
a reply.
Receiving a Call
1.
Select a conventional system and channel or turn Scan on
and make sure desired channel is in Scan list.
2. Wh
en the radio receives a call, the radio unmutes and the
channel name or number appears in the display.
Declaring an Emergency
1. Press and hold the red Emergency/Home button.
2. and are illuminated in the display and *TXEMER*
flashes in the display. After 2-3 seconds, turns off.
3. *TXEMER* and
remain illuminated in the display until the
emergency is cleared.
4. Press the PTT button and
reappears. Speak normally.
5.
Release the PTT button when transmission is complete.
Press and hold the Clear/Monitor button,
then
simultaneously press the emergency button to clear an
emergency (if enabled through programming).
For more detailed operating information and a list of options
and accessories, refer to the Operator’s Manual
(MM-013994-001 - available online at www.pspc.harris.com).