Why is my Hatco Food Warmer too hot?
If your Hatco Food Warmer is getting too hot, the temperature control might be set too high. Try changing the temperature to a lower setting. If the issue persists, the unit might be connected to an incorrect power supply, in that case, contact an Authorized Hatco Service Agent or Hatco for assistance.
Why is my Hatco Food Warmer not hot enough?
If your Hatco Food Warmer isn't hot enough, first allow the unit 15–20 minutes to preheat to the operating temperature. Also, check that the temperature control isn't set too low and adjust it to a higher setting. Ensure all drawers are completely closed. If the internal thermostat is defective, contact an Authorized Hatco Service Agent or Hatco for assistance.
How to prevent my product from drying out in the Hatco Food Warmer?
If the product in your Hatco Food Warmer is too dry, the drawer vent may be in the open position. Move the drawer vent to the closed position. Also, check if the optional water pan is empty or not installed; install it and/or fill it with clean water, controlling the moisture level using the drawer vents.
What to do if product is too moist in Hatco Food Warmer?
If the product in your Hatco Food Warmer is too moist, the drawer vent might be in the closed position, so move the drawer vent to the open position. If you have an optional water pan installed but don't need it, remove the water pan from the drawer.
What to do if my Hatco Food Warmer is not working?
If your Hatco Food Warmer isn't working, start by ensuring it's properly plugged into a power supply and that the POWER ON/OFF switch is in the ON position. Also, check if the circuit breaker has tripped and reset it if necessary. For defective POWER ON/OFF switch, thermostat or burned out heating element contact an Authorized Hatco Service Agent or Hatco for assistance.
What to do if my Hatco HDW-2 is not working at all?
If your Hatco Warming Drawer isn't working, first ensure it's properly plugged into a power supply and that the POWER switch is in the ON position. Check your circuit breaker and reset it if necessary. If these steps don't resolve the issue, it could be due to a defective power switch, thermostat, or a burned-out heating element, in which case you should contact an Authorized Hatco Service Agent or Hatco for assistance.
Why is my Hatco HDW-2 too hot?
If your Hatco Warming Drawer is getting too hot, the TEMPERATURE control might be set too high; try lowering it. It is also possible that the unit is connected to an incorrect power supply or that the internal thermostat is defective. In these cases, contact an Authorized Hatco Service Agent or Hatco for assistance.
Why is my Hatco Warming Drawer not hot enough?
If your Hatco Warming Drawer isn't hot enough, ensure you've allowed it 15–20 minutes to preheat. Also, check that the temperature control isn't set too low and that all drawers are completely closed. If the issue persists, the internal thermostat might be defective, and you should contact an Authorized Hatco Service Agent or Hatco for assistance.
What to do if product is too dry in Hatco HDW-2?
If the product in your Hatco Warming Drawer is too dry, make sure the drawer vent is in the closed position. Also, check if the optional water pan is empty or not installed; if so, install it and fill it with clean water. Control the level of moisture using the drawer vents.
What to do if product is too moist in Hatco HDW-2?
If the product in your Hatco Warming Drawer is too moist, ensure the drawer vent is in the open position. If you're using the optional water pan, it might not be needed; try removing it from the drawer.
Details about electrical cords and plugs supplied with the units.
Electrical specifications including voltage, watts, amps, and shipping weight for HDW-x models.
Electrical specifications for HDW-xN models, including voltage, watts, amps, and shipping weight.
Electrical specifications for HDW-xB models, including voltage, watts, amps, and plug configuration.
Electrical specifications for HDW-xBN models, including voltage, watts, amps, and shipping weight.
Electrical specifications for HDW-xBR models, including voltage, watts, amps, and shipping weight.
Details the capacity of standard drawers for various food items like rolls and ribs.
Provides width, depth, and height measurements for HDW-x and HDW-xN models.
Provides width, depth, and height measurements for HDW-xB and HDW-xBN models.
Provides width, depth, and height measurements for HDW-xBR models.
Covers unpacking, placement, and general installation guidelines for all models.
Details the process of installing legs or casters on freestanding HDW-x and HDW-xN units.
Guides on installing built-in HDW-xB, HDW-xBN, and HDW-xBR models into cabinets.
Explains how to control and monitor individual drawers using vents, switches, and knobs.
Step-by-step instructions for initial startup and safe shutdown of the drawer warmer.
Provides instructions for daily cleaning to preserve finish and performance of the unit.
Details the procedure for cleaning the water pan to remove lime and mineral deposits.
Explains the operation and settings of the digital temperature controller.
Details installation of 3" locking casters for freestanding units.
Lists available stainless steel food pans in various sizes.
General| Model Number | HDW-2 |
|---|---|
| Product Type | Warming Drawer |
| Construction | Stainless steel |
| Voltage | 120V |
| Certifications | UL, NSF |
To Next Page
