Why does my HATHASPACE HARMONY 600 always detect high levels of particulates?
If your HATHASPACE Air Cleaner is always detecting high levels of particulates, it might be operating in a very dusty environment. Consider turning the fan to HIGH.
What to do if the filter light is still on after replacing the filter on my HATHASPACE Air Cleaner?
If the filter light on your HATHASPACE Air Cleaner is still on after replacing the filter, you may have forgotten to reset the air purifier. Press the “Filter Light” button for 5 seconds to reset it.
Why is the air purification quality poor with my HATHASPACE HARMONY 600?
There are several reasons why your HATHASPACE Air Cleaner might have poor air purification quality: * A low speed is used, so increase the fan speed. * The airflow or the air outlet is blocked by packaging or other matter, so remove any blockage. * Filters installed incorrectly, so make sure the filters are installed correctly. * The unit is being used in open places, so close doors and windows while using the air purifier. * The applied area is larger than the effective range, so consider a larger air purifier. * The quality of the air in the room is very poor, so open the window to circulate new air. * The room layout is not good, so buy more air purifiers or change the layout if possible.
Why is the filter light on before 6 months on my HATHASPACE HARMONY 600?
If the filter light is on before 6 months on your HATHASPACE Air Cleaner, it could be because the appliance is run frequently or the air is highly polluted. In this case, replace the filters.
How to fix a HATHASPACE HARMONY 600 Air Cleaner that won't turn on?
If your HATHASPACE Air Cleaner cannot be turned on or does not respond to button controls, check the following: 1. Ensure the unit is properly plugged into an electrical outlet. 2. Plug into a different outlet in case the current outlet is damaged. If these steps don't work, the power cord may be damaged or the air purifier may have malfunctioned, and you should contact Customer Service.
Why is the airflow significantly reduced in my HATHASPACE HARMONY 600 Air Cleaner?
Reduced airflow in your HATHASPACE Air Cleaner can occur for several reasons: * Packaging may be blocking the airflow, so remove the packaging. * A low speed is being used, so increase the fan speed. * There is not enough clearance for the air inflow, so leave 20cm clearance on all sides of the air purifier. * The Pre-filter may be clogged by large particles, so clean the Pre-filter or replace the filter. * Filters are installed incorrectly, so make sure the filters are installed correctly.
What causes my HATHASPACE Air Cleaner to make unusual noises?
If your HATHASPACE Air Cleaner makes an unusual noise while the fan is on, it could be due to: packaging blocking the airflow (remove the packaging); the air purifier being on an inclined place making the fan blades rub with the air purifier’s lining (put the air purifier on even places). If neither of these is the cause, the air purifier may be damaged or a foreign object may be inside, so contact Customer Service.
Preliminary filter removing large particles like pet hair, dust, and debris.
Non-woven material capturing small particles to extend HEPA filter life.
Absorbs smoke, odors, and gases from the air.
High-efficiency filter capturing small micron particles like tobacco smoke and lead dust.
Details the functions of each button and indicator on the control panel.
Explains the color-coded air quality levels and corresponding PM2.5 concentration.
Describes how the particle sensor works in manual and auto modes.
Details the three levels of light brightness and how to set memory brightness.
Instructions on how to safely clean the air purifier unit with a soft cloth.
Step-by-step guide on how to remove and replace the air purifier filters.
General| Model | Harmony 600 |
|---|---|
| Pre-filter | Yes |
| Auto Mode | Yes |
| Sleep Mode | Yes |
| Warranty | 2 years |
| Type | Air Purifier |
| Filter Type | HEPA |
To Next Page
