EasyManua.ls Logo

Hayward SP2315X20XE - User Manual

Hayward SP2315X20XE
24 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
XE Pump Series
Owner’s Manual
TriStar
®
XE
MaxFlo
®
XE
Super Pump
®
XE
IS3200XE REV A
Contents
Pump Warnings...............2
Overview.........................5
Installation.....................6
Operation.......................9
Troubleshooting............14
Maintenance.................15
Winterization.................16
Sha Seal Change.........17
Replacement Parts........20
Hayward Pool Products
400 Connell Drive, Suite 6100,
Berkeley Heights, NJ 07922
Phone (908)-355-7995
www.hayward.com

Table of Contents

Questions and Answers

  • A
    Alicia GonzalezAug 19, 2025
    Why is there low flow in my Hayward SP2315X20XE Water Pump?
    • W
      wallerjohnnyAug 20, 2025
      Low flow in your Hayward Water Pump can stem from several issues. Air leaks in the suction line can cause bubbles at the return fittings; re-tighten suction and discharge connections with PTFE tape and inspect other plumbing. Other possible causes include undersized pool piping (correct the piping size), or a plugged, restricted, or damaged impeller (replace the impeller including a new seal assembly).
  • R
    Rebecca PhillipsAug 22, 2025
    What to do if my Hayward Water Pump has stalled?
    • S
      Steven WilcoxAug 22, 2025
      If your Hayward Water Pump has stalled, check the impeller, diffuser, shaft seal, and motor for any issues or binding.
  • M
    Mrs. Michelle GrayAug 25, 2025
    What to do if the motor current is too high in my Hayward SP2315X20XE?
    • F
      farmertylerAug 26, 2025
      If the motor current is too high in your Hayward Water Pump, check the impeller, diffuser, shaft seal, and motor for any issues or binding.
  • A
    Antonio AdamsAug 27, 2025
    What to do if my Hayward Water Pump motor will not start?
    • V
      Valerie RobinsonAug 27, 2025
      If your Hayward Water Pump motor won't start, begin by checking the wiring against the diagrams. Ensure the pump is correctly wired for the available voltage/current according to the data nameplate. Inspect for any loose or improper wiring, open switches or relays, tripped circuit breakers, or blown fuses, and correct them. Manually check the motor shaft for any obstructions, ensuring it rotates freely.
  • R
    robertjohnsonAug 30, 2025
    Why is my Hayward SP2315X20XE Water Pump so noisy?
    • A
      Andrew Cross MDAug 31, 2025
      A noisy Hayward Water Pump can be due to several reasons. Check for air leaks in the suction piping, which can cause cavitation, or restrictions/undersizing in the suction line. Low water levels in the pool or unrestricted discharge return lines can also contribute. Ensure the pump is mounted on a level surface and securely fastened. Foreign matter in the pump housing could also be the culprit. Also, motor bearings can become noisy due to wear, rust, overheating, or chemical exposure, leading to seal damage and water seepage. Replace seal leaks immediately.
  • S
    Stefanie GreeneSep 2, 2025
    What to do if my Hayward SP2315X20XE Water Pump motor shuts OFF and the LED is not Solid ON?
    • P
      Paul FloresSep 2, 2025
      If your Hayward Water Pump motor shuts off and the LED isn't solid, it's frequently caused by undersized wiring. Check for low voltage or power drops at the motor. Contact a qualified professional to verify the electrical connections.
  • J
    Jeffrey DiazSep 5, 2025
    What to do if my Hayward SP2315X20XE Water Pump motor hums, but does not start?
    • M
      michaelwilliamsSep 5, 2025
      If your Hayward Water Pump motor hums but doesn't start, it could be that the impeller is jammed with debris. Have a qualified repair professional open the pump and remove the debris.
  • A
    amandakingSep 7, 2025
    What does it mean if the IPM temperature is too high in my Hayward SP2315X20XE?
    • S
      Sandra DanielsSep 7, 2025
      If the IPM temperature is too high in your Hayward Water Pump, the motor airflow path should be checked for obstructions and cleared if present. Also, check the ambient temperature and compare it against the motor nameplate specifications.
  • M
    Mrs. Kara WilliamsSep 12, 2025
    What does it mean if the DC voltage is out of range in my Hayward Water Pump?
    • S
      Stephen RobertsSep 12, 2025
      If the DC voltage is out of range in your Hayward Water Pump, verify that the line voltage is within 10% of the pump's rated voltage at the terminal block. Also, ensure that power supply connections are properly made at the circuit breaker and terminal block, and that the voltage change jumper is correctly set for the intended line voltage connection.
  • S
    Samuel StevensSep 13, 2025
    What to do if the motor does not restart right away after power cycling and the LED is blinking on my Hayward SP2315X20XE Water Pump?
    • P
      Paula RichardsSep 13, 2025
      To resolve the issue of the motor not restarting immediately after power cycling with a blinking LED on your Hayward Water Pump, ensure the LED turns off completely by waiting at least 30 seconds before reapplying power to the pump.

Summary

Important Safety Instructions

General Safety Precautions

Covers essential safety guidelines, warnings, and cautions for pump operation and installation.

Installation

Pump Location and Mounting

Plumbing

Electrical

Wiring Requirements and Safety

Mandates for grounding, bonding, input power, and adherence to electrical codes for safe operation.

Wiring Connections

Operation and Control

Starting, Priming, and Controls

Procedures for initial start-up, priming the pump, and using the control button interface.

LED Indicator and Schedule Overview

Programming the Daily Schedule

Entering and Setting Intervals

Step-by-step guide to enter programming mode and select speeds for each interval.

Schedule Programming Completion

Saving Intervals and Example

Manual Override Functionality

Override Modes and Transitions

Priming Mode

Controlling the XE Pump

Troubleshooting Common Issues

Motor, Priming, Flow, and Noise Problems

Guides to diagnose and resolve motor failures, priming issues, low flow, and pump noise.

System Errors and Maintenance

Error Codes, Maintenance, and Storage

Shaft Seal Change - TriStar XE

Shaft Seal Change - MaxFlo XE

Shaft Seal Change - Super Pump XE

Seal Replacement Procedure

Detailed steps for removing and replacing the shaft seal assembly on the Super Pump XE pump.

Hayward SP2315X20XE Specifications

General IconGeneral
ModelSP2315X20XE
TypeAbove Ground Pool Pump
Horsepower1.5 HP
PhaseSingle Phase
SpeedSingle Speed
Warranty1 Year
Max RPM3450 RPM
Motor TypeTEFC
Connection Size2"

Related product manuals