USE ONLY HAYWARD GENUINE REPLACEMENT PARTS 1
VariFlo
®
Multiport
1 1/2” Filter Control Valve
Owner’s Manual
Model: SP0710X62 (Sand Filters)
TURN OFF PUMP BEFORE CHANGING VALVE POSITION
FUNCTIONS OF VALVE POSITIONS
VALVE SETTING
FLOW DIRECTION THROUGH VALVE
FILTER
PUMP - TOP - THROUGH FILTER - BOTTOM - RETURN
For normal filtration and vacuuming pool through
filter.
BACKWASH
PUMP -BOTTOM - THROUGH FILTER -TOP -WASTE
For cleaning filter.
RINSE
PUMP - TOP - THROUGH VALVE - WASTE
For initial start-up and clearing valve of debris after
backwashing.
WASTE
PUMP – THROUGH VALVE - WASTE
For vacuuming directly to waste, lowering pool level
and/or draining pool.
CLOSED
NO CIRCULATION PAST PUMP POR
For shutting off all flow to filter and pool.
RECIRCULATE
PUMP – THROUGH VALVE - RETURN
For bypassing filter, but circulating pool water.
WINTERIZING:
Drain and winterize filter and pump per manufacturer's
instructions. To drain water from VariFlo® Multiport
valve—depress and rotate valve handle and place
handle pointer between any detente positions.
CAUTION –Spring
Hazard – Release of
Valve spring
compression can
cause personal injury.
To avoid, only remove
handle pin if servicing
key O-ring. Remove
handle pin before
slowly removing Cover
screws in an alternate
pattern.
REF
NO.
PART NUMBER DESCRIPTION
NO.
REQ’D
1SPX0710X
Handle, Standard 1
2 SPX0710XZ7 Pin, for Handle 1
3 SPX0710Z16 Non-Metallic Bearin
(Pack of 5) 1
SPX0710G Valve Position Label 1
4SPX0710Z1
Cover screw set with nuts (Set of 6) 1
5SPX0710
Z5 Cover O-rin
1
6SPX0603SSprin
1
7 SPX0710Z62 Spring Washer Set (Set of 2) 1
8SPX0735G
O-ring & TFE Shaft seal set 1
SPX0710
¼” Plastic Pipe Plu
1
9 SPX0710XD Valve Seat Gasket 1
10 SPX0710xC Key 1
11 SX200Z4PAK2 Valve O-rin
(Set of 2) 1
SPX0710BA17 Key, Cover and Handle Assy 1
SPX0710M
Sight Glass with Gasket 1
SX200Z9 Gasket for Sight Glass 1
SPX0710X62A
Valve body with gasket and pipin
GENERAL
1. Proper fitting make-up is hand tight plus one to 1-
1/2 turns maximum. Always use Teflon pipe tape
or Permatex No.2 for connections to provide a
good, "living" seal.
IMPORTANT: Do not over tighten pipe fittings.
2. SERVICING VALVE: If it becomes necessary to
service or gain access to the key or valve seat
gasket:
a. Set handle in “Winterizing” position.
b. Remove cover screws.
c. Lift cover and key assembly out.
3. RE-ASSEMBLY VALVE:
a. Wipe debris from cover 0-ring.
b. Set handle in a “Winterizing” position. Align
flat edge on cover with body. Press down to
seat assembly.
c. Secure assembly to body with cover screws
and nuts. Tighten cover screws evenly and
alternately.
Do not over tighten.
-
ea
an
o
ow a
nstruct
ons in this owner’s manual and on the equipment.
Failure to follow instructions can cause severe injury and/or death.
Hayward Pool Products
620 Division Street, Elizabeth, NJ 07207
Phone: (908) 355-7995
WWW.HAYWARD.COM
IS0710X62 REV B
To Next Page
Need help?
General
