Heat & Glo 6000GLX-IPI-S User Manual

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. H • 4/07
1
Models:
6000GLX-IPI-S
6000GLX-IPI-R
6000GLX-IPILP-S
6000GLX-IPILP-R
Owner’s Manual
Installation and Operation
Para obtener un ejemplar en Español de este
Manual del propietario, visite www.heatnglo.com.
Pour demander un exemplaire en français de ce
Manuel du propriétaire, visitez www.heatnglo.com.
• Donotstoreorusegasolineorotheram-
mable vapors and liquids in the vicinity of
this or any other appliance.
• What to do if you smell gas
- Do not try to light any appliance
- Do not touch any electrical switch. Do not
use any phone in your building.
- Immediately call your gas supplier from a
neighbor’s phone. Follow the gas suppli-
er’s instructions.
- If you cannot reach your gas supplier, call
theredepartment.
• Installation and service must be performed
byaqualiedinstaller,serviceagency,orthe
gas supplier.
WARNING: If the information in these
instructions is not followed exactly, a re
or explosion may result causing property
damage, personal injury, or death.
DO NOT DISCARD THIS MANUAL
CAUTION
This appliance may be installed as an OEM installation in
manufactured home (USA only) or mobile home and must be
installed in accordance with the manufacturer’s instructions and
the manufactured home construction and safety standard, Title
24 CFR, Part 3280 or Standard for Installation in Mobile Homes,
CAN/CSA Z240MH.
This appliance is only for use with the type(s) of gas indicated
on the rating plate.
Installation and service of this appliance should be
performed by qualied personnel. Hearth & Home
TechnologiessuggestsNFIcertiedorfactorytrained
professionals, or technicians supervised by an NFI
certiedprofessional.
• Leave this manual with
party responsible for use
and operation.
DO NOT
DISCARD
WARNING
• Important operating
an d ma int enanc e
instructions included.
• Read, understand and follow
these instructions for safe
installation and operation.
In the Commonwealth of Massachusetts:
• installation must be performed by a licensed plumber
orgastter;
See Table of Contents for location of additional
Commonwealth of Massachusetts requirements.
This appliance has been supplied with an integral barrier
to prevent direct contact with the xed glass panel. Do
NOT operate the appliance with the barrier removed.
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
HOT! DO NOT TOUCH.
SEVERE BURNS MAY RESULT.
CLOTHING IGNITION MAY RESULT.
• CAREFULLY SUPERVISE children in same room as
appliance.
• Alert children and adults to hazards of high temperatures.
• Do NOT operate with protective barriers open or
removed.
• Keep clothing, furniture, draperies and other combustibles
away.
Glass and other surfaces are hot during
operation and cool down.
• Keep children away.

Heat & Glo 6000GLX-IPI-S Specifications

General

Brand	Heat & Glo
Model	6000GLX-IPI-S
Category	Indoor Fireplace
Language	English

Summary

Safety Precautions and Warnings

Listing and Code Approvals

Massachusetts Installation Requirements

Framing and Clearances

Clearances to Combustibles

Detailed clearance requirements to combustible materials for safe installation.

Vent Termination Locations

Minimum Termination Clearances

Specifies minimum vertical and horizontal clearances for vent termination based on roof pitch.

Termination Clearance Parameters and Alcove Applications

Vent Information and Diagrams

Flue Restrictor Adjustment and Installation

Step-by-step guide for installing and adjusting the flue restrictor for optimal performance.

Flue Restrictor Settings and Diagrams

Details how to match vertical vent length to restrictor settings and shows related diagrams.

Vent Clearances and Framing

Pipe Clearances and Wall Penetrations

Appliance Preparation

Securing and Leveling the Appliance

Steps for properly positioning, leveling, and securing the appliance to the framing.

Installing Vent Pipe

Assembling Vent Sections

Step-by-step guide for assembling DVP vent sections, including securing and alignment.

Assembling Specific Vent Sections (MI and Slip)

Instructions for assembling MI sections and DVP-12A slip sections, including cutting and securing.

Heat Shields and Horizontal Termination

Requirements and procedures for installing heat shields and horizontal termination caps.

SL-D Pipe Vent Assembly

Instructions for assembling SL-D series vent sections, locking components, and adding firestops.

Wall Shield Firestops and Horizontal Termination

Procedures for installing wall shield firestops for horizontal runs and termination cap guidelines.

Roof Flashing and Vertical Termination Cap

Steps for installing roof flashing and vertical termination caps, including minimum heights.

Gas Information

Fuel Conversions and Gas Pressures

Gas Connection Requirements

Electrical Information

Intellifire Ignition and Junction Box

Details on Intellifire ignition system wiring and junction box installation procedures.

Intellifire Ignition Wiring Diagram

A detailed wiring diagram for the Intellifire Pilot Ignition system, showing component connections.

Appliance Setup

Installing the Refractory

Step-by-step instructions for installing the refractory panels inside the firebox.

Refractory Installation Details

Details for positioning optional refractory standoff brackets and installing top refractory pieces.

Positioning the Gas Logs

Step-by-step instructions for correctly positioning the gas logs on the burner grate.

Gas Log Placement - Logs 2-4

Instructions for positioning logs #2, #3, and #4 according to their specific placement guides.

Gas Log Placement - Logs 5-7

Instructions for positioning logs #5, #6, and #7 according to their specific placement guides.

Air Shutter Adjustment

Guidance on adjusting the air shutter for optimal flame appearance and troubleshooting sooting issues.

Operating Instructions

Pre-Lighting Appliance Checks

Lighting the Appliance (IPI Ignition)

Step-by-step instructions for lighting the appliance using the Intellifire Pilot Ignition system.

Troubleshooting

Intellifire Ignition System Issues

Common problems and corrective actions for the Intellifire ignition system, including no spark or pilot issues.

Intellifire Ignition System Issues (Continued)

Further troubleshooting steps for Intellifire ignition system issues like pilot light problems and gas supply checks.

Maintenance and Servicing