Heat & Glo SL-750TRS-IPI-E User Manual

1
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. U • 11/13
Models:
SL-750TRS-IPI-E
SL-550TRS-IPI-E
SL-750TRS-E
SL-550TRS-E
SL-350TRS-IPI
• DO NOT store or use gasoline or other fl am-
mable vapors and liquids in the vicinity of this
or any other appliance.
• What to do if you smell gas
- DO NOT try to light any appliance.
- DO NOT touch any electrical switch. DO
NOT use any phone in your building.
- Immediately call your gas supplier from a
neighbor’s phone. Follow the gas suppli-
er’s instructions.
- If you cannot reach your gas supplier, call
the fi re department.
• Installation and service must be performed
by a qualifi ed installer, service agency, or the
gas supplier.
WARNING: If the information in these
instructions is not followed exactly, a fi re
or explosion may result causing property
damage, personal injury, or death.
Owner’s Manual
Installation and Operation
DO NOT DISCARD THIS MANUAL
NOTICE
Installation and service of this appliance should be
performed by qualifi ed personnel. Hearth & Home
Technologies suggests NFI certifi ed or factory trained
professionals, or technicians supervised by an NFI
certifi ed professional.
• Leave this manual with
party responsible for use
and operation.
DO NOT
DISCARD
• Important operating
and maintenance
instructions included.
• Read, understand and follow
these instructions for safe
installation and operation.
In the Commonwealth of Massachusetts installation must be
performed by a licensed plumber or gas fi tter.
See Table of Contents for location of additional Commonwealth
of Massachusetts requirements.
Para obtener un ejemplar en Español de este
Manual del propietario, visite www.heatnglo.com.
Pour demander un exemplaire en français de ce Manuel
du propriétaire, visitez www.heatnglo.com.
WARNING
A barrier designed to reduce the risk of burns
from the hot viewing glass is provided with this
appliance and shall be installed.
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
This appliance may be installed as an OEM
installation in manufactured home (USA
only) or mobile home and must be installed
in accordance with the manufacturer’s
instructions and the Manufactured Home
Construction and Safety Standard, Title 24
CFR, Part 3280 in the United States, or the
Standard for Installation in Mobile Homes,
CAN/CSA Z240 MH Series, in Canada.
This appliance is only for use with the type(s)
of gas indicated on the rating plate. This
appliance is not convertible for use with other
gases, unless a certifi ed kit is used.

Heat & Glo SL-750TRS-IPI-E Specifications

General

Fuel Type	Natural Gas or Liquid Propane
Ignition Type	IPI (Intermittent Pilot Ignition)
Vent Type	Direct Vent
Log Set Material	Ceramic Fiber
Efficiency	70%
Warranty	Limited Lifetime

Summary

Listing and Code Approvals

Appliance Certification

Details the certification standards and laboratories for the appliance.

BTU Specifications

Provides a table of BTU input specifications for different models and gas types.

High Altitude Installations

Explains adjustments for reduced input rates at higher elevations in USA and Canada.

Electrical Codes

Specifies adherence to local codes, NEC, and Canadian Electric Code for wiring.

Operating Instructions

Gas Fireplace Safety

Provides essential safety warnings for operating the gas fireplace, including hot glass.

Lighting Instructions (IPI)

Step-by-step guide for lighting the intermittent pilot ignition (IPI) system.

Lighting Instructions (Standing Pilot)

Detailed procedure for lighting the pilot on standing pilot models.

Maintenance and Service

Maintenance Tasks-Homeowner

Lists annual maintenance tasks for homeowners, like glass cleaning and checking doors.

Maintenance Tasks-Qualified Service Technician

Outlines annual tasks for qualified technicians, including burner and ignition checks.

Getting Started

Design and Installation Considerations

Key factors for designing and installing the direct vent gas appliance.

Tools and Supplies Needed

Lists necessary tools and building supplies for installation.

Framing and Clearances

Selecting Appliance Location

Guidance on choosing an appliance location considering clearances.

Clearances

Specifies minimum air space clearances to combustibles for the appliance and vent pipe.

Mantel and Wall Projections

Details minimum clearances for mantels and wall projections above the appliance.

Vent Information and Diagrams

Approved Pipe

Information on approved Hearth & Home Technologies DVP or SLP venting systems.

Measuring Standards

Defines standards used for vertical and horizontal vent measurements.

Vent Clearances and Framing

Pipe Clearances to Combustibles

Guidelines for maintaining air space between vent pipe and combustibles.

Wall Penetration Framing

Instructions for framing holes and installing wall shield firestops.

Installing Vent Pipe (DVP and SLP Pipe)

Assemble Vent Sections (DVP Pipe Only)

Steps for assembling DVP vent sections to the firebox.

Assemble Vent Sections (SLP Pipe Only)

Instructions for attaching SLP vent components to appliance collars.

Assemble Slip Sections

Procedure for assembling slip sections for vent pipe.

Gas Information

Gas Pressure

Details required gas pressures for Natural Gas and Propane.

Gas Connection

Guidance on connecting the gas supply line to the appliance.

High Altitude Installations

Instructions for adjusting appliance performance at high altitudes.

Electrical Information

Wiring Requirements

Specifies electrical wiring requirements and safety precautions.

IntelliFire Ignition System Wiring

Wiring instructions for the IntelliFire ignition system.

Standing Pilot Ignition System Wiring

Wiring guidelines for the standing pilot ignition system.

Finishing

Splatter Guard

Instructions for installing and removing the splatter guard.

Mantel and Wall Projections

Minimum vertical and horizontal dimensions for combustibles around the appliance.

Facing Material

Guidelines for applying facing and finishing materials.

Doors

Information on certified doors and finishing material thickness.

Appliance Setup

Remove Shipping Materials

Instructions for removing packaging materials from the appliance.

Clean the Appliance

Guidance on cleaning the appliance interior before use.

Lava Rock, Mineral Wool/Ember Placement

Instructions for correctly placing lava rock and ember material.

Install Refractory

Steps for installing the refractory panels inside the firebox.

Troubleshooting

Standing Pilot Ignition System

Troubleshooting guide for issues with the standing pilot ignition system.

IntelliFire Ignition System

Troubleshooting guide for issues with the IntelliFire ignition system.

Reference Materials

Appliance Dimension Diagram

Diagram showing actual appliance dimensions for reference.

Vent Components Diagrams

Illustrations and specifications of various vent system components.

Service Parts

Listings of available service parts for different models.