Heat & Glo SL-7X-IFT User Manual

1
Heat & Glo • SL-3X-IFT, SL-5X-IFT, SL-7X-IFT, SL-9X-IFT Installation Manual • 2472-980 Rev. Q • 3/20
Installation Manual
Installation and Appliance Setup
INSTALLER: Leave this manual with party responsible for use and operation.
OWNER: Retain this manual for future reference.
NOTICE: DO NOT discard this manual!
In the Commonwealth of Massachusetts installation must be
performed by a licensed plumber or gas tter.
See Table of Contents for location of additional Commonwealth
of Massachusetts requirements.
• DO NOT store or use gasoline or other am-
mable vapors and liquids in the vicinity of this
or any other appliance.
• What to do if you smell gas
- DO NOT try to light any appliance.
- DO NOT touch any electrical switch. DO
NOT use any phone in your building.
- Leave the building immediately.
- Immediately call your gas supplier from
a neighbor’s phone. Follow the gas sup-
plier’s instructions.
- If you cannot reach your gas supplier, call
the re department.
• Installation and service must be performed
by a qualied installer, service agency, or the
gas supplier.
WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly
could result in serious injury, death, or
property damage.
Models:
SL-3X-IFT
SL-5X-IFT
SL-5XLP-IFT
SL-7X-IFT
SL-7XLP-IFT
SL-9X-IFT
This appliance may be installed as an OEM
installation in manufactured home (USA
only) or mobile home and must be installed
in accordance with the manufacturer’s
instructions and the Manufactured Home
Construction and Safety Standard, Title 24
CFR, Part 3280 in the United States, or the
Standard for Installation in Mobile Homes,
CAN/CSA Z240 MH Series, in Canada.
This appliance is only for use with the type(s)
of gas indicated on the rating plate. This
appliance is not convertible for use with other
gases, unless a certied kit is used.
DANGER
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
A barrier designed to reduce the risk of
burns from the hot viewing glass is provided
with this appliance and shall be installed for
the protection of children and other at-risk
individuals.
Pour demander un exemplaire en français de ce Manuel du
propriétaire, visitez www.heatnglo.com/translations.

Heat & Glo SL-7X-IFT Specifications

General

Brand	Heat & Glo
Model	SL-7X-IFT
Category	Indoor Fireplace
Language	English

Summary

Product Specific and Safety Information

Appliance Certification and Specifications

Details on appliance certification, glass, and BTU ratings.

Installation Requirements and Codes

Covers high altitude, material specs, electrical codes, and CA warnings.

Massachusetts Installation Requirements

Specific requirements for MA, including CO detectors, signage, inspection.

Manufacturer Venting System Requirements

Guidelines for provided and not provided venting systems.

Getting Started

Design and Installation Considerations

Key factors before beginning installation, including location and vent config.

Framing and Clearances

Clearances to Combustibles

Specifies minimum required clearances to combustible materials.

Constructing the Appliance Chase

Guidelines for building a chase structure for the appliance and vent system.

Termination Location and Vent Information

Vent Termination Minimum Clearances

Minimum clearance requirements for vent termination locations.

Vent Terminal Clearances

Approved Vent Pipe Types

Vent Diagrams and Rules

Vent Clearances and Framing

Pipe Clearances to Combustibles

Maintain air space clearance to vent pipe and avoid packing insulation.

Wall Penetration Framing and Firestops

Ceiling Firestop and Floor Penetration Framing

Appliance Preparation

Vent Collar Preparation

Securing and Leveling the Appliance

Procedures for properly positioning, securing, and leveling the appliance.

Venting and Chimneys

Assemble Vent Sections (DVP Pipe)

Assemble Slip Sections (SLP Pipe)

Vertical Termination Requirements

Horizontal Termination Requirements

Electrical Information

General Electrical Information

General safety warnings and wiring compliance notes.

Junction Box Installation

Electrical Service and Repair

Safety precautions and procedures for servicing electrical components.

Wiring Requirements

Details on IntelliFire Touch ignition system wiring and power sources.

Gas Information

Fuel Conversion and Gas Pressure

Information on fuel compatibility, conversion, and gas pressure requirements.

Gas Connection Procedures

Steps for connecting the gas supply line to the appliance.

Air Shutter Setting Adjustment

Burner Identification and Verification

Appliance Setup

Remove Fixed Glass Assembly

Setup Overview and Refractory Installation

General setup overview and detailed steps for installing refractory components.

Log Installation and Placement

Detailed instructions for installing and correctly positioning the log set.

IntelliFire Touch Control System Setup

Steps for setting up the IntelliFire Touch remote control system.

Re-install Fixed Glass Assembly

Decorative Front Installation