Heat & Glo SL-750TR-D User Manual

Heat & Glo • SL-550 / 750 / 950TR-D • 2044-985 Rev. J • 6/06
1
Models:
SL-950TR-D
SL-750TR-D
SL-550TR-D
Owner’s Manual
Installation and Operation
• Do not store or use gasoline or other flamma-
ble vapors and liquids in the vicinity of this or
any other appliance.
• What to do if you smell gas
- Do not try to light any appliance
- Do not touch any electrical switch. Do not
use any phone in your building.
- Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
- If you cannot reach your gas supplier, call
the fire department.
• Installation and service must be performed by
a qualified installer, service agency, or the gas
supplier.
WARNING: If the information in these
instructions is not followed exactly, a fire
or explosion may result causing proper-
ty damage, personal injury, or death.
This appliance has been supplied with an integral barrier
to prevent direct contact with the fixed glass panel. Do
NOT operate the appliance with the barrier removed.
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
HOT! DO NOT TOUCH.
SEVERE BURNS MAY RESULT.
CLOTHING IGNITION MAY RESULT.
WARNING
• Keep children away.
• CAREFULLY SUPERVISE children in same room as
appliance.
• Alert children and adults to hazards of high
temperatures.
• Do NOT operate with protective barriers open or
removed.
• Keep clothing, furniture, draperies and other
combustibles away.
Glass and other surfaces are hot during
operation and cool down.
DO NOT DISCARD THIS MANUAL
CAUTION
Important operating and
maintenance instruc-
tions included.
This appliance may be installed as an OEM installation in
manufactured home (USA only) or mobile home and must
be installed in accordance with the manufacturer’s instruc-
tions and the manufactured home construction and safety
standard, Title 24 CFR, Part 3280 or Standard for Installa-
tion in Mobile Homes, CAN/CSA Z240MH.
This appliance is only for use with the type(s) of gas indi-
cated on the rating plate.
Installation and service of this appliance should be
performed by qualified personnel. Hearth & Home
Technologies suggests NFI certified or factory-trained
professionals, or technicians supervised
by an NFI certified professional.
•
••
DO NODO NO
DO NODO NO
DO NO
TT
TT
T
DISCARDDISCARD
DISCARDDISCARD
DISCARD
Read, understand and follow
these instructions for safe
installation and operation.
Leave this manual with
party responsible for
use and operation.
In the Commonwealth of Massachusetts:
• installation must be performed by a licensed plumber or
gas fitter;
See Table of Contents for location of additional
Commonwealth of Massachusetts requirements.

Heat & Glo SL-750TR-D Specifications

General

Vent Type	Direct Vent
Type	Direct Vent
Fuel Type	Natural Gas or Propane
Ignition Type	Electronic
Ignition	IPI (Intermittent Pilot Ignition)
Control Type	Remote Control
Warranty	Limited Lifetime

Summary

Safety and Warning Information

General Safety and Warning Information

Crucial safety guidelines for installation and operation to prevent fire hazards and ensure proper function.

Specific Warnings

Critical warnings about fire/explosion risks, gas leaks, touching hot surfaces, and child supervision.

Approvals and Codes

Appliance Certification

Details on tested standards and listing by applicable laboratories for Heat & Glo models.

Installation Codes Compliance

Requirements to conform to local, national, and Canadian installation codes for safe setup.

High Altitude Installations

Guidelines for adjusting input rating and orifice size for installations above 2,000 feet.

Massachusetts Requirements

Carbon Monoxide Detector Installation

Mandates for installing hard-wired and battery-operated CO detectors on each dwelling level.

Signage Requirements

Specification for a permanent sign indicating gas vent location and clearance needs.

Getting Started

Introducing Heat & Glo Gas Appliances

Overview of direct vent gas appliances and the information contained within the manual.

Pre-installation Preparation

Steps to ensure safe installation, including checking parts and reading instructions.

Appliance Installation

Constructing the Appliance Chase

Guidelines for building a vertical box-like structure to enclose the appliance and vent system.

Locating and Framing the Appliance

Requirements for space, clearance, and framing when positioning the appliance.

Vent System Installation

Procedures for installing vent components, firestops, and terminations.

Gas Controls, Supply, and Wiring

Procedures for connecting gas controls, supply lines, and electrical wiring.

Finishing, Trim, and Lighting

Steps for finishing the installation, adding trim, and safely lighting the appliance.

Appliance Maintenance and Servicing

Routine Maintenance Tasks

Guidelines for regular servicing like ember replacement, burner cleaning, and flame sensor checks.

Vent System and Glass Cleaning

Procedures for inspecting the vent system and cleaning the glass door.