To Next PageTo Next Page
Need help?Do you have a question about the Heat & Glo SL-350TRS-IPI and is the answer not in the manual?
General| Style | Traditional |
|---|---|
| Fuel Type | Natural Gas or Propane |
| Vent Type | Direct Vent |
| Glass Type | Ceramic |
| Control Type | Remote Control |
| Log Set Material | Ceramic Fiber |
| Weight | 150 lbs |
| Warranty | Limited Lifetime |
| Type | Gas Fireplace |
| Ignition Type | IPI (Intermittent Pilot Ignition) |
Appliance certification details and standards compliance.
Specifications for the tempered glass used in the appliance.
Details on the appliance's BTU output for different models.
Guidelines for installing the appliance at high altitudes.
Defines materials considered non-combustible for installation.
Defines materials considered combustible for installation.
Requirements for electrical wiring and grounding.
Specific installation requirements for Massachusetts.
Essential safety precautions for operating the gas fireplace.
General overview of the fireplace components and features.
Information regarding the optional fan kit accessory.
Required clearances around the fireplace for safe operation.
Guidelines for installing decorative doors and fronts.
Information about the fixed glass assembly.
Instructions for operating controls like remotes and wall switches.
Pre-operation checks and tasks before lighting the fireplace.
Step-by-step guide for lighting the Intermittent Pilot Ignition system.
Step-by-step guide for lighting the standing pilot system.
Procedures to follow after the fireplace has been lit.
Common issues and their solutions for fireplace operation.
Routine maintenance tasks that can be performed by the homeowner.
Maintenance tasks requiring a qualified service technician.
Overview of the typical appliance installation system.
Key considerations for designing and installing the appliance.
List of tools and supplies required for installation.
Procedure for inspecting the appliance and its components.
Guidance on choosing the appropriate location for the appliance.
Instructions for building the chase structure for the appliance.
Required air space clearances to combustibles and vent pipe.
Specifications for mantel and wall projections near the appliance.
Minimum clearances required for vent termination to prevent fire risk.
Information on approved venting pipes for the appliance.
Key to abbreviations used in vent diagrams.
Guidelines for using elbows in vent installations.
Standards used for vent pipe measurements.
Proper usage and support for flexible vent pipe.
Diagrams illustrating various vent configurations and components.
Maintaining safe air space clearances between vent pipe and combustibles.
Framing requirements for wall penetrations with vent pipe.
Procedure for installing ceiling firestops for vent pipes.
Instructions for installing attic insulation shields for vent pipes.
Steps for preparing the appliance for top venting.
Steps for preparing the appliance for rear venting.
Instructions for assembling DVP series vent pipes.
Instructions for assembling SLP series vent pipes.
Procedure for assembling slip sections of the vent pipe.
Installing decorative ceiling components for SLP venting.
Procedure for installing metal roof flashing for vent pipes.
Steps for assembling and installing the storm collar.
Instructions for installing the vertical termination cap.
Installing decorative wall components for SLP venting.
Requirements for heat shields in horizontal vent terminations.
Instructions for installing horizontal termination caps.
Information on converting the appliance to different gas types.
Required gas pressures for optimal appliance performance.
Steps and safety precautions for connecting the gas supply.
Adjustments for installing the appliance at high altitudes.
Electrical wiring standards and precautions for installation.
Wiring instructions for the IntelliFire ignition system.
Wiring instructions for the standing pilot ignition system.
Electrical requirements for optional accessories like fans or remotes.
Troubleshooting guide for issues with the standing pilot ignition system.
Instructions for installing and removing the splatter guard.
Clearances and requirements for mantels and wall projections.
Guidelines for applying facing materials around the appliance.
Information on available doors and finishing material thickness.
Details on hearth systems that elevate the appliance.
Procedure for removing the fixed glass assembly.
Instructions for removing shipping materials.
Steps for cleaning the appliance before operation.
Information on installing approved accessories.
Correct placement of lava rock and ember material.
Instructions for installing the refractory components.
Step-by-step guide for installing the log set.
Details and warnings regarding the fixed glass assembly.
Instructions for installing trim kits and surrounds.
Adjusting the air shutter for optimal flame appearance.
Troubleshooting common issues with the standing pilot system.
Troubleshooting common issues with the IntelliFire ignition system.
Diagram showing the physical dimensions of the appliance.
Diagrams of various vent system components and their dimensions.
List of available service parts with part numbers.
Contact details for the manufacturer and dealers.
