Heat & Glo SL-750TR-IPI-E User Manual

1Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
Models:
SL-550TR-E
SL-750TR-E
SL-950TR-E
SL-550TR-IPI-E
SL-750TR-IPI-E
SL-950TR-IPI-E
Owner’s Manual
Installation and Operation
DO NOT DISCARD THIS MANUAL
NOTICE
• Leave this manual with
party responsible for use
and operation.
DO NOT
DISCARD
• Important operating
and maintenance
instructions included.
• Read, understand and follow
these instructions for safe
installation and operation.
In the Commonwealth of Massachusetts installation must be
performed by a licensed plumber or gas fi tter.
See Table of Contents for location of additional Commonwealth
of Massachusetts requirements.
Para obtener un ejemplar en Español de este
Manual del propietario, visite www.heatnglo.com.
Pour demander un exemplaire en français de ce Manuel
du propriétaire, visitez www.heatnglo.com.
This appliance may be installed as an OEM
installation in manufactured home (USA
only) or mobile home and must be installed
in accordance with the manufacturer’s
instructions and the Manufactured Home
Construction and Safety Standard, Title 24
CFR, Part 3280 in the United States, or the
Standard for Installation in Mobile Homes,
CAN/CSA Z240 MH Series, in Canada.
This appliance is only for use with the type(s)
of gas indicated on the rating plate. This
appliance is not convertible for use with other
gases, unless a certifi ed kit is used.
DANGER
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
A barrier designed to reduce the risk of
burns from the hot viewing glass is provided
with this appliance and shall be installed for
the protection of children and other at-risk
individuals.
• DO NOT store or use gasoline or other fl am-
mable vapors and liquids in the vicinity of this
or any other appliance.
• What to do if you smell gas
- DO NOT try to light any appliance.
- DO NOT touch any electrical switch. DO
NOT use any phone in your building.
- Leave the building immediately.
- Immediately call your gas supplier from
a neighbor’s phone. Follow the gas sup-
plier’s instructions.
- If you cannot reach your gas supplier, call
the fi re department.
• Installation and service must be performed
by a qualifi ed installer, service agency, or the
gas supplier.
WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly
could result in serious injury, death, or
property damage.

Heat & Glo SL-750TR-IPI-E Specifications

General

Fuel Type	Natural Gas or Propane
Heat Output	Up to 50, 000 BTU/H
Vent Type	Direct Vent
Control Type	Remote Control
Warranty	Limited Lifetime Warranty
Type	Fireplace
Ignition System	IPI (Intermittent Pilot Ignition)
Viewing Area Dimensions	32-1/2 x 21-1/2 inches
Log Set Material	Ceramic Fiber

Summary

Owner's Manual Installation and Operation

Homeowner Reference Information

Section to record fireplace model, serial number, and purchase details.

Listing Label Information and Location

Details on locating the rating plate with specific fireplace information.

User Guide

Operating Instructions

Covers safe operation, lighting, and basic fireplace functions.

Maintenance and Service

Details homeowner and technician tasks for upkeep and repair.

Getting Started

Covers initial setup, system overview, tools, and inspection.

Framing and Clearances

Provides guidelines for selecting location and building the fireplace chase.

Termination Locations

Specifies minimum clearances for vent termination points.

Installer Guide

Vent Information and Diagrams

Details approved vent pipes, table key, elbows, and measurement standards.

Vent Clearances and Framing

Covers pipe clearances to combustibles and wall penetration framing.

Appliance Preparation

Instructions for preparing the appliance for vent installation.

Installing Vent Pipe (DVP and SLP Pipe)

Step-by-step guide for assembling and installing DVP and SLP vent pipes.

Gas Information

Covers fuel conversion, gas pressure, connection, and high altitude.

Electrical Information

Details wiring requirements and specific ignition system wiring.

Finishing

Instructions for applying splatter guards, mantels, and facing materials.

Appliance Setup

Covers removal of glass, cleaning, accessories, and log/ember placement.

Troubleshooting

Provides solutions for common pilot and burner ignition issues.

Reference Materials

Includes dimension diagrams, vent components, service parts, and contacts.