HELLER KPF 2001 B User Manual

TEMPERATURE CONTROL (ONLY by remote control)
- Press
to switch on the appliance.
- Press + or -
to set the setting temperature from 1
(the light °C is on).
If room temperature
setting temperature 25°C
, the display as the picture
- Press
to cancel the temperature setting
(the light °C
is off) and to choose the heating
The heater working on full power when the room temperature is
The heater working on half power when the room temperature is between
setting temperature.
The heater switches off when the room temperature is higher than the setting temperature
working 30 seconds to make inside cool to protect component, then fan stop, the unit enter into standby.
The heater switches on again when the room temperature falls 2°C below the setting temperature.
TURN-ON, TURN-OFF
(by control panel and remote control)
Turn-on in stand-by mode :
- Press
to set the appointment turn
The display automatically decreases 1 hour for each hour passed. When the
appointment power-
on time arrived, the product will automatically turns on. The default
setting temperature is 23°C.
If not setting the setting temperature and weekly program,
turn-off after continuous
working 12hours and enter into stand
For example to set appointment turn
Turn-off in running mode
Press
to set the appointment turn
When the appointment power-
off time arrived, the product will automatically turns off. The default setting
temperature is 23°C
For example to set appointment turn
5 seconds
Weekly time and Window open detection
SET CURRENT TIME (ONLY by remote control)
- Press
to switch on the appliance.
- Press SET to display the hour.
- Press + or -
to set the current hour (
- Press SET
again to display the minute.
- Press + or -
to set the current minute (
27
TEMPERATURE CONTROL (ONLY by remote control)
to switch on the appliance.
to set the setting temperature from 1
0°C to 49°C
If room temperature
15°C,
, the display as the picture
to cancel the temperature setting
is off) and to choose the heating
on half power ( ) or full power (
The heater working on full power when the room temperature is
4
°C lower than the setting temperature.
The heater working on half power when the room temperature is between
0° and 2°C lower than the
The heater switches off when the room temperature is higher than the setting temperature
working 30 seconds to make inside cool to protect component, then fan stop, the unit enter into standby.
The heater switches on again when the room temperature falls 2°C below the setting temperature.
(by control panel and remote control)
to set the appointment turn
-on time in 1-12 hours (the light is on).
The display automatically decreases 1 hour for each hour passed. When the
on time arrived, the product will automatically turns on. The default
If not setting the setting temperature and weekly program,
the unit will automatically
working 12hours and enter into stand
-by.
For example to set appointment turn
-on time to 8 hours
to set the appointment turn
-off time in 1-12 hours (the light is on)
off time arrived, the product will automatically turns off. The default setting
For example to set appointment turn
-off time to 8 hours
5 seconds
Weekly time and Window open detection
SET CURRENT TIME (ONLY by remote control)
to switch on the appliance.
to set the current hour (
00 to 23).
again to display the minute.
to set the current minute (
00 to 59).
).
°C lower than the setting temperature.
0° and 2°C lower than the
The heater switches off when the room temperature is higher than the setting temperature
. The fan
working 30 seconds to make inside cool to protect component, then fan stop, the unit enter into standby.
The heater switches on again when the room temperature falls 2°C below the setting temperature.
The display automatically decreases 1 hour for each hour passed. When the
on time arrived, the product will automatically turns on. The default
the unit will automatically
off time arrived, the product will automatically turns off. The default setting
- Press SET
again to display the day of week.
- Press + or -
to set the current day (
d4 = Thursday, d5 = Friday, d -
Press
For example, Wednesday 9
:30 , Setting temperature = 25°C :
SET
Hour
Minutes
SET
Setting temperature
T
o check the current time and setting temperature, press
If main switch off or power cut off
, it need reset the time
SET WEEKLY PROGRAM (ONLY by remote control)
The current time must be set before any programming.
- Press
to switch on the appliance.
1. Press P
to enter into weekly program setting (the light
2. Press DAY
to set the day of program activation (
3. Press EDIT
to set the time period number (
4. Press TIME/ON to set the turn-
on time (
Cannot set to minutes.
5. Press TIME/OFF to set the turn-
off
Cannot set to minutes.TIME/OFF can not be less than TIME/ON.
6. Press + or -
to set the setting temperature of this time period.
7. Press OK to confirm the setting.
8.
Repeat steps 3 to 7 to set another time period number for the same day.
U
p to 6 programs are available for each day of the week.
9.
Repeat steps 2 to 8 to set the others days of the week.
- Press P
to active the weekly program (the light
-
After the above setting are completed and
t
o check the setting time of each day
When the turn-
on time is same as th
If the setti
ng temperature is not set, the default setting temperature is 23°C.
23°C
, the appliance is not switch on.
28
again to display the day of week.
to set the current day (
d1 = Monday,d2=Tuesday,d3=Wednesday,
Press
OK to confirm the setting).
:30 , Setting temperature = 25°C :
SET
Minutes
Day
o check the current time and setting temperature, press
SET again.
, it need reset the time
SET WEEKLY PROGRAM (ONLY by remote control)
The current time must be set before any programming.
to switch on the appliance.
to enter into weekly program setting (the light
P is on).
to set the day of program activation (
d1, d2, d7...),
to set the time period number (
P1, P2,...P6),
on time (
00, 01, 02 ..., 24)
off
time (00, 01, 02,..., 24)
Cannot set to minutes.TIME/OFF can not be less than TIME/ON.
to set the setting temperature of this time period.
Repeat steps 3 to 7 to set another time period number for the same day.
p to 6 programs are available for each day of the week.
Repeat steps 2 to 8 to set the others days of the week.
to active the weekly program (the light
P is on), or to disable it (the light
P
After the above setting are completed and
P program is work, press
DAY / EDIT TIME/ON
o check the setting time of each day
and time period.
on time is same as th
e turn-off time, the appliance is in
stand by mode.
ng temperature is not set, the default setting temperature is 23°C.
If room temperature higher
, the appliance is not switch on.
P
is off).
DAY / EDIT TIME/ON
and TIME/OFF
stand by mode.
If room temperature higher

HELLER KPF 2001 B Specifications

General

Brand	HELLER
Model	KPF 2001 B
Category	Heater
Language	English