EasyManua.ls Logo

HIAB X-Duo 044 - User Manual

HIAB X-Duo 044
124 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
This operator’s manual is an Original Instruction and applies to cranes with serial
number from:
BL044DO00001, BL078DU00001, BL088DO00001, BL102DU00001,
BL112DU00001
2018-01
Operator's Manual GB
HIAB X-Duo
044/078/088/102/112

Table of Contents

Questions and Answers

  • T
    Theresa ColeAug 12, 2025
    Why are there irregular slewing movements and unusual noises in HIAB X-Duo 044 cranes with continuous slewing system?
    • R
      robertsonscottAug 12, 2025
      To resolve irregular slewing movements and unusual noises in HIAB Construction Equipment cranes with a continuous slewing system, first, top up the oil tank if the hydraulic system has insufficient oil. Second, ensure that the gear box has enough oil; if not, top it up to the required level. Next, lubricate the bearing while slewing. If the problem continues, the bearing assemblies or pinion might be damaged, and it's recommended to visit a HIAB service workshop.
  • D
    Dr. Ryan MontgomeryAug 16, 2025
    Why is the hydraulic pump making noise in my HIAB Construction Equipment?
    • P
      Paul ShortAug 16, 2025
      If the hydraulic pump of your HIAB Construction Equipment is making noise, it could be due to several reasons. First, check if the oil tank filler breather is clogged. If it is, you will need to go to a HIAB service workshop. Second, verify that the oil level in the tank is not too low; if it is, top up the oil tank. Finally, the hydraulic pump itself might be faulty, which also requires a visit to a HIAB service workshop.
  • D
    Dale AndrewsAug 19, 2025
    Why can't the boom system keep the load height on my HIAB Construction Equipment?
    • R
      Richard FordAug 19, 2025
      If the boom system of your HIAB Construction Equipment cannot keep the load height and goes down by itself, it may be due to damaged load holding valves on the first or second boom, or internal cylinder leakage. In either case, it is recommended to visit a HIAB service workshop.
  • L
    Lisa ColeAug 23, 2025
    What to do if the stabilizer leg cylinder can't keep the truck load on my HIAB X-Duo 044?
    • B
      blackkennethAug 23, 2025
      If the stabiliser leg cylinder of your HIAB Construction Equipment cannot keep the truck load and it goes inwards, it could be due to a damaged check valve, cylinder internal leakage, or a soft ground surface. If the ground surface is soft, set the stabiliser leg again onto the ground or add an extra support plate between the cylinder and the ground. For a damaged check valve or cylinder internal leakage, go to a HIAB service workshop.
  • F
    Faith BrownAug 27, 2025
    What to do if one function of the HIAB Construction Equipment controller does not work?
    • A
      Andrew SheppardAug 27, 2025
      If one function of the HIAB Construction Equipment controller does not work, it could be because one lever of the controller was not in neutral at start up. Push in the Stop button, make sure that all levers are in neutral, and then release the Stop button.
  • K
    kathleen90Aug 30, 2025
    Why do the boom extensions shake during extending/retracting on my HIAB X-Duo 044?
    • C
      christopher84Aug 31, 2025
      If the boom extensions of your HIAB Construction Equipment shake during extending/retracting, it could be due to cylinder internal leakage or a loose sequence screw in the cylinder head. For cylinder internal leakage, go to a HIAB service workshop. If the sequence screw in the cylinder head is loose, tighten the screw in the right position.
  • S
    shawnatkinsonSep 3, 2025
    Why can't the boom extensions keep the load height on my HIAB Construction Equipment?
    • P
      Paige JenningsSep 4, 2025
      If the boom extensions of your HIAB Construction Equipment cannot keep the load height and they move out by themselves, it could be due to a damaged extension load holding valve or cylinder internal leakage. In either case, it is recommended to visit a HIAB service workshop.
  • W
    William HughesSep 7, 2025
    What to do if the add-on equipment does not work properly on my HIAB X-Duo 044 Construction Equipment?
    • A
      anthonyscottSep 7, 2025
      If the add-on equipment (rotator, hoist, etc.) on your HIAB Construction Equipment does not work properly, the connectors may not be properly connected. Reconnect the add-on equipment according to the instructions.

HIAB X-Duo 044 Specifications

General IconGeneral
BrandHIAB
ModelX-Duo 044
CategoryConstruction Equipment
LanguageEnglish

Related product manuals