Need help?Do you have a question about the Hifonics TXi 3400 and is the answer not in the manual?
General| Total Harmonic Distortion (THD) | <0.05% |
|---|---|
| Fuse Rating | 40A x 2 |
| Signal-to-Noise Ratio | 95dB |
| Input Sensitivity | 0.2V - 6V |
| Phase Shift | 0° - 180° |
| Frequency Response | 10Hz - 30kHz |
| Subsonic Filter | 15Hz - 35Hz |
General guidelines for mounting the amplifier for optimal performance and safety.
Step-by-step guide for physically mounting the amplifier unit securely.
Instructions for securely connecting the amplifier's ground wire to the vehicle chassis.
How to connect the remote turn-on wire from the head unit to the amplifier.
Guide for connecting the main power supply to the amplifier, including fuse placement.
Explanation of the amplifier's integrated fuses and their role in protection.
Controls for adjusting crossover frequencies for speakers or subwoofers.
Control for boosting bass frequencies at 45Hz.
RCA input and output connections for signal routing.
Adjusts the input sensitivity of the amplifier to match the head unit.
Explanation of the Power and Protect LEDs.
Switch to select crossover mode (HP, LP/BP, FULL).
Terminal for connecting a remote bass control.
How to connect speakers and RCA cables for stereo operation.
How to set the X-Over switch for this configuration.
Steps to set the input level for optimal performance.
Recommended setting for Bass Boost in this mode.
Note on Bass Remote usage for this configuration.
How to connect for mono subwoofer operation.
Setting the X-Over switch for mono subwoofer mode.
Steps to set the input level for mono subwoofer.
Recommended setting for Bass Boost in this mode.
How to use the Bass Remote for subwoofers.
Adjusts low-pass filter frequency for channels 3/4.
Bass boost control for channels 3/4.
Input sensitivity adjustment for all channels.
Adjusts high-pass filter frequency for channels 1/2 and 3/4.
RCA input and output connections for the amplifier.
Explanation of Power and Protect LEDs.
Crossover control for channels 3/4.
Crossover control for channels 1/2.
Selection for input signal routing (2CH/4CH/DUPE).
Connecting speakers and RCA for 4-channel stereo operation.
Setting crossover switches for 4-channel stereo.
Setting input level for 4-channel stereo.
Bass boost setting for channels 3/4 in 4-channel mode.
Note on Bass Remote usage in this configuration.
Connecting for 3-channel operation with two bridged subwoofers.
Setting the input mode for 3-channel operation.
Crossover settings for the subwoofer channels.
Crossover settings for the front/rear channels.
Setting input level for 3-channel operation.
Bass boost setting for subwoofer channels.
Usage of Bass Remote for subwoofers.
Connecting for mixed stereo and bridged subwoofer operation.
Crossover settings for front/rear channels.
Crossover settings for subwoofer channels.
Setting input level for mixed configuration.
Bass boost setting for subwoofer channels.
Bass remote usage for subwoofers.
Steps to diagnose and fix when the amplifier fails to power on.
Troubleshooting common audio noise issues.
Resolving lack of audio output on all channels.
Identifying and fixing hiss or white noise in the audio.
Diagnosing and resolving issues with stereo sound or low output.
Understanding and resolving amplifier protection mode activation.
Addressing noise caused by electrical interference in the vehicle.
Troubleshooting engine-dependent noise issues.
Diagnosing and fixing persistent whining noises.
RMS and MAX power ratings for different impedances and configurations.
Damping factor, S/N ratio, channel separation, THD&N, input sensitivity, impedance.
Specifications for crossover filters and bass boost.
Fuse ratings and physical dimensions of the amplifiers.
To Next Page