HIKOKI DS 14DBSL - User Manual

Questions and Answers

K
Karen ChoiSep 9, 2025
What to do if HIKOKI Power Tool bits can’t be attached or fall off?
- A
  Andrew Powell Jr.Sep 10, 2025
  If HIKOKI Power Tool bits can’t be attached or fall off, it may be because the shape of the attachment portion doesn’t match. The chucking diameter of the keyless chuck is 1.5 mm to 13 mm. Use a bit that falls within the stated range. If the lock of the keyless chuck is worn, contact a HiKOKI Authorized Service Center and arrange to have the old keyless chuck replaced with a new one.
F
Franklin HunterSep 8, 2025
What to do if holes can’t be smoothly drilled with my HIKOKI Power Tool?
- W
  William SimsSep 8, 2025
  If holes can’t be smoothly drilled with your HIKOKI Power Tool, it could be that the drill is worn, so replace it with a new drill. Also, the rotation speed might not be appropriate, so adjust the rotation speed (HIGH/LOW) to match the material to be drilled. Check that the drill is rotating in the correct direction and switch to forward rotation if needed.
D
Dr. Ricardo GarciaSep 7, 2025
Why is HIKOKI Power Tool battery usage time short?
- B
  Benjamin ShawSep 7, 2025
  If the battery usage time is short even though the HIKOKI Power Tool battery is fully charged, the battery’s life is likely depleted. Replace the battery with a new one.
E
Elizabeth HansenAug 22, 2025
Why doesn't my HIKOKI Drill run?
- B
  Bill StewartAug 23, 2025
  If your HIKOKI Drill isn't running, it could be due to no remaining battery power, in which case you should charge the battery. Alternatively, the battery might not be securely attached. Push it in until you hear a click.
C
Christian RogersSep 5, 2025
Why does my HIKOKI Power Tool battery take a long time to charge?
- J
  John SmithSep 5, 2025
  A HIKOKI Power Tool battery can take a long time to charge if the temperature of the battery, the charger, or the surrounding environment is extremely low. Try charging the battery indoors or in another warmer environment. Also, check if the charger’s vents are blocked, causing its internal components to overheat, and avoid blocking the vents. If the cooling fan is not running, contact a HiKOKI Authorized Service Center for repairs.
K
Kristen SmithSep 3, 2025
What to do if my HIKOKI Power Tool doesn’t run?
- D
  Danielle AndersonSep 3, 2025
  If your HIKOKI Power Tool doesn’t run, it could be due to no remaining battery power. Charge the battery. Another possibility is that the battery isn’t securely attached. Push in the battery until a click is heard.
L
Lisa KellySep 2, 2025
Why does my HIKOKI Power Tool suddenly stop working?
- S
  Sarah WattsSep 2, 2025
  Your HIKOKI Power Tool might have stopped suddenly because it was overburdened. Remove the cause of the overburdening. Alternatively, the battery or tool may have overheated. In this case, allow the tool and battery to thoroughly cool.
C
Christine EdwardsSep 1, 2025
Why can’t I pull the switch on my HIKOKI DS 14DBSL?
- A
  Amanda LongSep 1, 2025
  If you can’t pull the switch on your HIKOKI Drill, the forward/reverse selector button may be positioned halfway. Press the button firmly into position for the desired direction of rotation.
A
Adam OsbornAug 31, 2025
Why is the pilot lamp rapidly flickering red, and battery charging doesn’t begin on my HIKOKI Drill?
- J
  John KimAug 31, 2025
  If the pilot lamp is rapidly flickering red, and battery charging doesn’t begin on your HIKOKI Drill, the battery may not be inserted all the way. Insert the battery firmly. Also, there may be foreign matter in the battery terminal or where the battery is attached, so remove any foreign matter.
A
Andrea MurphyAug 29, 2025
Why pilot lamp blinks red and battery charging doesn’t begin on HIKOKI DS 14DBSL Drill?
- B
  billy20Aug 30, 2025
  If the pilot lamp blinks red and battery charging doesn’t begin on your HIKOKI Drill, the battery might not be inserted all the way. Insert the battery firmly. If left alone, the battery will automatically begin charging if its temperature decreases, but this may reduce battery life. It is recommended that the battery be cooled in a well-ventilated location away from direct sunlight before charging it.