Why does Hilti HDE 500-A22 Dispenser battery run down more quickly than usual?
If the Hilti Dispenser battery is draining faster than normal, it might be due to a very low ambient temperature. Allow the battery to warm up slowly to room temperature.
Why is no mortar dispensed from the mixing nozzle of my Hilti Dispenser?
If no mortar is dispensed from the mixing nozzle of your Hilti Dispenser, the mortar in the mixing nozzle may have hardened. To resolve this, unscrew the mixing nozzle containing the hardened mortar and fit a new mixing nozzle.
How to fix Hilti HDE 500-A22 Dispenser power tool that does not work?
If your Hilti Dispenser power tool doesn't work, there are a few potential causes. First, make sure the battery is fully inserted by pushing it in until it engages with an audible double click. Second, check if the battery is low and replace it with a charged one. Lastly, ensure that the dispensing mode selector switch is not set to “0”; select the desired dispensing volume instead.
Why does my Hilti HDE 500-A22 Dispenser power tool or battery get very hot?
If your Hilti Dispenser power tool or battery gets very hot, it could be due to overloading the tool by exceeding application limits. Check the power and performance rating of the product to ensure it's suitable for the job. Refer to the “Technical data” section.
What to do if Hilti HDE 500-A22 foil pack holder cannot be swiveled into the tool?
If the Hilti Dispenser foil pack holder cannot be swiveled into the tool, check if the foil pack is fully pushed into the holder. Push it in as far as it will go. Also, ensure the piston rods are fully pulled back by pressing the release button and pulling them all the way back.
What to do if no mortar is dispensed from the Hilti HDE 500-A22 Dispenser mixing nozzle?
If no mortar is dispensed from the Hilti Dispenser mixing nozzle, it's likely that the mortar in the mixing nozzle has hardened. Unscrew the mixing nozzle containing the hardened mortar and fit a new mixing nozzle.
How to fix Hilti Dispenser when no mortar is dispensed from the mixing nozzle?
If no mortar is being dispensed from the mixing nozzle of your Hilti Dispenser, it's likely that the mortar in the mixing nozzle has hardened. To resolve this, unscrew the mixing nozzle containing the hardened mortar and fit a new one.
Why Hilti Dispenser power tool or battery gets very hot?
If your Hilti Dispenser power tool or battery is getting very hot, it could be due to overloading the tool by exceeding application limits. Ensure that you check the power and performance rating of the product before using it to confirm it's suitable for the task. If overloading isn't the issue, there may be an electrical fault.
What to do if the foil pack holder cannot be swiveled into my Hilti HDE 500-A22 Dispenser tool?
If the foil pack holder cannot be swiveled into the Hilti Dispenser tool: * The foil pack may not be pushed fully into the holder. Push the foil pack into the foil pack holder as far as it will go. * The piston rods may not be pulled back fully. Press the release button and pull the piston rods all the way back.
What to do if no mortar is dispensed from the mixing nozzle of my Hilti Dispenser?
If no mortar is coming out of the mixing nozzle of your Hilti Dispenser, the mortar in the mixing nozzle may have hardened. Unscrew the mixing nozzle containing the hardened mortar and fit a new mixing nozzle.
Read this documentation before initial operation or use for safe handling and use.
Explains signal words like DANGER, WARNING, CAUTION, and symbols used in the document and illustrations.
Details product type, generation, and serial number for service inquiries.
States compliance with directives and standards, and location of technical documentation.
Provides essential safety instructions for work area, electrical, and personal safety.
Emphasizes compliance with all safety instructions and usage guidelines before operating the tool.
Step-by-step guide on how to insert the battery into the dispenser.
Step-by-step guide on how to remove the battery from the dispenser.
Instructions for correctly inserting the foil pack holder and foil pack into the dispenser.
Provides a detailed labeled diagram of the HDE 500-A22 dispenser and its components.
Specifies the intended application and compatible consumables for the HDE 500-A22 dispenser.
Lists the items included with the dispenser and where to find information on other approved products.
Details the weight and rated voltage specifications for the HDE 500-A22.
Provides a table to diagnose common issues and their possible causes and actions.
Instructions and precautions for safely transporting the tool and batteries.
Guidelines for safe and proper storage of the tool and batteries to prevent damage.
Specific instructions for transporting and storing the dispenser unit.
Information on recycling Hilti tools and safe disposal of batteries, avoiding household waste.
To Next Page
General
