What to do if the battery does not engage with an audible double click in my Hilti HDE 500-A22 Dispenser?
If the battery does not engage with an audible double click in your Hilti Dispenser, the retaining lugs on the battery may be dirty. Clean the retaining lugs and push the battery in until it engages.
What to do if the foil pack holder does not engage with an audible click in my Hilti HDE 500-A22 Dispenser?
If the foil pack holder on your Hilti Dispenser doesn't engage with an audible click: * The retaining lugs may be dirty. Clean the retaining lugs. * The retaining lugs may be defective. Insert a different foil pack holder.
What to do if Hilti HDE 500-A22 power tool does not work and all four LEDs flash?
If your Hilti Dispenser power tool isn't working and all four LEDs are flashing, it could be due to several reasons. The overload cut-out might be activated because the mortar in the mixing nozzle has hardened, in which case you should replace the static mixer (mixing nozzle). Alternatively, the dispensing pressure required might be too high for the tool; try increasing the foil pack temperature or selecting a power tool that better suits the application. Finally, the foil pack could be empty, requiring you to replace it.
What to do if the foil pack holder cannot be swiveled into my Hilti HDE 500-A22 Dispenser tool?
If the foil pack holder cannot be swiveled into the Hilti Dispenser tool: * The foil pack may not be pushed fully into the holder. Push the foil pack into the foil pack holder as far as it will go. * The piston rods may not be pulled back fully. Press the release button and pull the piston rods all the way back.
What to do if my Hilti HDE 500-A22 Dispenser power tool does not work and one LED flashes?
If your Hilti Dispenser power tool isn't working and one LED is flashing, it could be due to: * A low battery. Change the battery and charge the empty battery. * The battery is either too hot or too cold. Try changing the battery.
What to do if no mortar is dispensed from the mixing nozzle of my Hilti Dispenser?
If no mortar is coming out of the mixing nozzle of your Hilti Dispenser, the mortar in the mixing nozzle may have hardened. Unscrew the mixing nozzle containing the hardened mortar and fit a new mixing nozzle.
Why is my Hilti HDE 500-A22 power tool not working and all four LEDs are flashing?
If your Hilti Dispenser power tool is not working and all four LEDs are flashing, it could be due to: * The overload cut-out is activated because mortar in the mixing nozzle has hardened. Replace the static mixer (mixing nozzle). * The overload cut-out is activated because the dispensing pressure required is too high for the tool. Increase the foil pack temperature and select a power tool suitable for the application. * The foil pack is empty. Replace the empty foil pack.
What to do if my Hilti Dispenser power tool does not work?
If your Hilti Dispenser power tool isn't working, consider these possibilities: * The battery may not be fully inserted. Push it in until you hear a double click. * The battery may be low. Replace the battery and charge the empty one. * The dispensing mode selector switch may be set to “0”. Select the desired dispensing volume.
What to do if the foil pack holder does not engage with an audible click on my Hilti HDE 500-A22 Dispenser?
If the foil pack holder on your Hilti Dispenser does not engage with an audible click, the retaining lugs may be dirty. Clean the retaining lugs.
Why does the Hilti HDE 500-A22 battery run down quickly?
If the battery of your Hilti Dispenser runs down more quickly than usual, it could be due to a very low ambient temperature. Allow the battery to warm up slowly to room temperature.
Read this documentation before initial operation or use for safe handling and use.
Explains signal words like DANGER, WARNING, CAUTION, and symbols used in the document and illustrations.
Details product type, generation, and serial number for service inquiries.
States compliance with directives and standards, and location of technical documentation.
Provides essential safety instructions for work area, electrical, and personal safety.
Emphasizes compliance with all safety instructions and usage guidelines before operating the tool.
Step-by-step guide on how to insert the battery into the dispenser.
Step-by-step guide on how to remove the battery from the dispenser.
Instructions for correctly inserting the foil pack holder and foil pack into the dispenser.
Provides a detailed labeled diagram of the HDE 500-A22 dispenser and its components.
Specifies the intended application and compatible consumables for the HDE 500-A22 dispenser.
Lists the items included with the dispenser and where to find information on other approved products.
Details the weight and rated voltage specifications for the HDE 500-A22.
Provides a table to diagnose common issues and their possible causes and actions.
Instructions and precautions for safely transporting the tool and batteries.
Guidelines for safe and proper storage of the tool and batteries to prevent damage.
Specific instructions for transporting and storing the dispenser unit.
Information on recycling Hilti tools and safe disposal of batteries, avoiding household waste.
To Next Page
General
