What does error F54 mean on my Hisense Dishwasher?
If your Hisense Dishwasher displays error code F54, it indicates overfilling water. Turn off the water tap and contact your nearest service centre. To avoid water leakage outside the dishwasher, do not remove the plug from the wall socket until the water tap on the supply line has been turned off!
Why does the Hisense Dishwasher control panel not react when pressed?
If the control panel of your Hisense Dishwasher doesn't respond, it might be because you pressed it too quickly after opening the door. Wait a moment and try again. Also, make sure the door is open, as the control panel only works when the door is open. Finally, the control panel may be dirty, so clean it with a dry or slightly damp cloth.
What to do if my Hisense Dishwasher shows F12 error?
If your Hisense Dishwasher displays error code F12, it indicates a water inlet fault. First, ensure that the water tap is turned on. Next, check the outer filter on the inlet hose for any blockages. Refer to the 'Unblocking the inlet hose filter' section in the Care and Cleaning chapter for instructions. If the issue continues, contact your nearest service center.
What does F67 error mean on a Hisense HV673C60UK Dishwasher?
If your Hisense Dishwasher displays error code F67, it means there is a water inlet fault. Make sure the water tap is on and check the outer filter on the inlet hose for blockages. See the 'Unblocking the inlet hose filter' section in the Care and Cleaning chapter for instructions. If the problem continues, contact your nearest service centre.
What does F10 error mean on a Hisense Dishwasher?
If your Hisense Dishwasher displays error code F10, it means there is overfilling water. Clear the drainage pump. See the chapter Care and cleaning. If the problem persists, contact your nearest service centre.
What does F52 error mean on a Hisense HV673C60UK Dishwasher?
If your Hisense Dishwasher displays error code F52, it indicates a water level fault. You should clean the coarse and fine filters. Also, check the outer filter on the inlet hose to ensure it is not blocked. If the problem persists, contact your nearest service centre.
What does error F11 mean on my Hisense HV673C60UK?
If your Hisense Dishwasher displays error code F11, it indicates a water outlet fault. See 'Water remains in the dishwasher' under 'Problem' in the table below. If the problem persists, contact your nearest service centre.
What does error F40 mean on my Hisense Dishwasher?
If your Hisense Dishwasher displays error code F40, it indicates an inlet valve leakage. Turn off the water tap and contact your nearest service centre.
What does F41 error mean on a Hisense HV673C60UK Dishwasher?
If your Hisense Dishwasher displays error code F41, it means there's a heater fault. Turn off the water tap, remove the plug from the wall socket, and contact your nearest service centre.
What does error F45 mean on my Hisense HV673C60UK Dishwasher?
If your Hisense Dishwasher displays error code F45, it indicates a diverter fault. Contact your nearest service centre.
Explains the importance of water hardness and how to adjust settings for optimal results.
Guidance on selecting and dosing dishwasher detergent and using compartments.
Details on various wash programs including Auto, Eco, Intensive, Glass, Hygiene, Night, and Self-clean.
Guide to downloading, installing, and setting up the ConnectLife app.
Steps to connect the dishwasher to WiFi and pair devices.
Procedures to unblock the drainage pump and inlet hose filter.
Actions to resolve specific error codes displayed by the dishwasher.
Resolving common problems like unresponsive controls or door issues.
Solutions for network symbol absence, connection failure, and pairing errors.
Critical safety instructions and initial setup steps for installation.
Instructions for connecting drainage and water supply hoses.
Information regarding the dishwasher's electrical connection requirements.
General| Energy Rating | C |
|---|---|
| Noise emission class | B |
| Control panel colour | Black |
| Built-in display | Yes |
| Tub material | Stainless steel |
| Inlet hose length | 1.5 m |
| Outlet hose length | 1.5 m |
| Cord length | 1.5 m |
| Delayed start timer | Yes |
| AquaStop function | Yes |
| Child lock | Yes |
| Adjustable feet | Yes |
| Upper basket adjustable height | Yes |
| Cutlery compartment type | Basket |
| Power consumption (off) | 0.5 W |
| Connected load | 1900 W |
| AC input voltage | 220-240 V |
| AC input frequency | 50 Hz |
| Width | 598 mm |
| Half Load Option | Yes |
| Type | Built-in |
| Washing programs | Auto, Intensive, Eco, Glass, Rapid, Hygiene, Soak |
| Appliance placement | Built-in |
| Depth | 600 mm |
| Wash Programs | Auto, Eco, Intensive, Quick wash, Sensor wash, Soak, Hygiene |
| Delayed start | 24 h |
To Next Page