Hisense WFXE7012 User Manual (English)

Questions and Answers:

N
nguyenalisonAug 16, 2025
What to do if Hisense WFXE7012 Washer shows error code F01?
- M
  Mr. Michael SolisAug 16, 2025
  If the Hisense Washer displays the failure code “F01”, it indicates that the appliance has none or insufficient water supply. To resolve this, check if the water tap is fully open and there is sufficient water supply pressure. Inspect the water hose for any kinks and ensure that the mesh filters of the water supply are not blocked. Also, check if the water hose is frozen. After resolving the issue, restart the program by pressing “Start/Pause”. If the problem continues, unplug the appliance and contact After-Sales Service.
D
dhuynhAug 19, 2025
What to do if Hisense WFXE7012 shows error code F03?
- R
  Ronald JohnsonAug 19, 2025
  If the Hisense Washer displays the failure code “F03”, it means that waste water is not being pumped out. To fix this, check the drain hose for kinks and make sure the pump or the filter isn't blocked. Ensure the water has cooled before draining the appliance. Also, check if the drain hose is frozen. If the fault persists after checking these, unplug the appliance and contact After-Sales Service.
Q
qhillAug 22, 2025
How to troubleshoot Hisense WFXE7012 Washer that won't start?
- K
  krista97Aug 22, 2025
  If your Hisense washer isn't starting, check that the mains plug is properly inserted into the socket and that the wall socket is functioning correctly by testing it with another appliance. Ensure the door is completely closed and that you've pressed the “Start/Pause” button.
D
dpetersenAug 25, 2025
Why does my Hisense WFXE7012 Washer keep stopping mid-cycle?
- S
  Shane PearsonAug 25, 2025
  If the Hisense Washer stops during the program, it could be due to several reasons. Check if the “Rinse Hold” indicator is lit; if so, press the “Start/Pause” button to terminate this option and start the drain process. Ensure the door is closed and the “Start/Pause” button is pressed again. Also, too much foam inside the machine could trigger a kill-foam routine, and the machine will restart automatically after a period. It’s also possible the washing machine’s safety system has been activated.
W
warnersuzanneAug 27, 2025
Why are the spin results poor on my Hisense WFXE7012 Washer?
- L
  Lisa HansonAug 27, 2025
  If the final spin results of your Hisense washer are poor, and the laundry is still too wet, try removing some articles and repeating the spin cycle. Excessive foam can also prevent proper spinning, so ensure you are using the correct amount of detergent. Also, check that the spin speed selector is not set to “0”.
E
Evan BergAug 30, 2025
Why is there detergent residue in my Hisense WFXE7012 Washer drawer after washing?
- C
  Courtney MartinezAug 30, 2025
  If you find residue from detergent and additives left in the detergent drawer of your Hisense washer after a wash, ensure that the cover grid of the softener chamber and the separator of the main wash chamber are correctly installed in the detergent dispenser and that all parts are clean. Check that sufficient water is entering the machine and that the mesh filters of the water supply are not blocked. Also, verify that the position of the separator in the main wash chamber is correctly adapted for the use of powder or liquid detergent.
R
Ryan OwensSep 2, 2025
What to do if Hisense WFXE7012 Washer shows error code UNB?
- V
  vanessa83Sep 2, 2025
  If the Hisense Washer displays the failure code “UNB”, it indicates an unbalance alarm. To resolve this, switch off the appliance by pressing the “ On/Off ” button for 2 seconds, rearrange the clothes inside, then select the spin program and start it again. If the fault persists, unplug the appliance and contact After-Sales Service.
Y
Yolanda LozanoSep 4, 2025
What to do if Hisense WFXE7012 Washer displays failure codes F04-F07?
- J
  Joshua HudsonSep 5, 2025
  If the Hisense Washer displays a failure code between “F04” and “F07”, it indicates that the electronic module has failed. To attempt a fix, switch the appliance off by pressing the “Power” button for 2 seconds and then select the desired program. If the fault continues, unplug the appliance and contact After-Sales Service.
J
James HooperSep 7, 2025
What to do if Hisense WFXE7012 Washer shows error code F13?
- C
  cameronalvaradoSep 7, 2025
  If the Hisense Washer displays the failure code “F13”, it indicates an abnormal door lock. Verify that the door is closed properly and then press the “start/pause” button. If the fault persists, unplug the appliance and contact After-Sales Service.
T
thompsonjasonSep 10, 2025
What to do if Hisense WFXE7012 shows error code F14?

Hisense WFXE7012 Specifications

General

Door hinge	Left
Control type	Buttons, Rotary
Display type	LED
Loading type	Front-load
Product color	White
Built-in display	Yes
Custom panel-ready	No
Appliance placement	Freestanding
Energy efficiency scale	A+++ to D
Power consumption (off)	0.49 W
Energy consumption washing per cycle	0.84 kWh
Annual water consumption washing	9390 L
Annual energy consumption washing	170 kWh
Drum capacity	7 kg
Cycle time (max)	278 min
Residual moisture	53 %
Spin-drying class	B
Maximum spin speed	1200 RPM
Noise level (spin)	72 dB
Noise level (wash)	57 dB
Left-on mode duration	3 min
Adjustable temperature	-
Number of washing programs	8
Cycle time (quick washing program)	15 min
Package depth	480 mm
Package width	660 mm
Package height	880 mm
Package weight	54000 g