--- 27 ---
7. Remove the Retaining Ring for D12 Shaft [34], Hex. Socket Hd. Bolt M5 x 16 [73] and Spring Washer M5 [74].
Then the Hinge Plate [75] can be removed.
8. Remove the four Machine Screws M4 x 10 [37] to remove the Hinge Cover [38]. Remove the Machine Screw
(W/Washers) M4 x 12 (Black) [17] and the Nylon Clip [18]. Press the Encoder [33] turning clockwise and
secure it with the Machine Screw M5 x 20 [29].
NOTE: When reinstalling the Hinge Ass'y [43] to the Turn Table Ass'y [108], loosen the Machine Screws
M5 x 20 [29] securing the Encoder [33] (about one turn) and move the Encoder [33] to engage
with Gear (B) [68].
9. Remove the four Machine Screws (W/Washers) M5 x 16 [103] to remove Table Insert (B) [102] and Table Insert
(A) [101] from the Turn Table Ass'y [108].
10. Remove the Machine Screw (W/Washers) M4 x 16 [109] to remove Cord Cover (A) [110]. Disconnect the
connector between Cord (A) 310 mm [123] and Cord (C) 300 mm [124]. Then it can be drawn out toward the
rear of the Hinge Ass'y [43]. Remove Shaft (D) [35] from the Nylon Nut M12 [72]. Then the Washer M6 [36],
Hinge Ass'y [43] and Liner (B) [65] can be removed from the Turn Table Ass'y [108].
11. Disconnect the connector of Cord (A) 310 mm [123] from the Encoder [127]. Remove the Machine Screw
M5 x 20 [29] and Bolt Washer M6 [30]. Remove Spring (C) [31] with a flat-blade screwdriver. Then the
Encoder [33] can be removed from the Hinge Ass'y [43].
12. Remove the two Hex. Socket Hd. Bolts M8 x 16 [78] and two Spring Washers M8 [77]. Remove the Side
Handle [82]. Remove the Spring Plate [76] from the Turn Table Ass'y [108].
NOTE: When reassembling after removal of the Spring Plate [76], adjust the squareness of the TCT Saw
Blade 305 mm-D25.4 Hole-NT32 [250] to Fence (A) [172] and Fence (B) [150].
13. Press the Encoder [127] turning clockwise onto the back of the Turn Table Ass'y [108] and secure it with the
Machine Screw M5 x 20 [130].
NOTE: When reinstalling the Turn Table Ass'y [108] to the Base Ass'y [167], loosen the Machine Screw
M5 x 20 [130] securing the Encoder [127] (about one turn) and move the Encoder [127] to engage
with Gear (A) [160]. Adjust the squareness of the TCT Saw Blade 305 mm-D25.4 Hole-NT32 [250] to
Fence (A) [172] and Fence (B) [150].
14. Remove the Nylon Nut M8 [104] and Washer (F) [105] to remove the Turn Table Ass'y [108] from the Base
Ass'y [167].
15. Remove the Machine Screw M4 x 8 [133] to remove the Dust Cover [132].
16. Disconnect the connector of Cord (A) 100 mm [112] from the Encoder [127]. Remove the Machine Screw
M5 x 20 [130] and remove Spring (C) [126] with a flat-blade screwdriver. Then the Encoder [127] can be
removed from the Turn Table Ass'y [108].
To Next Page
Loading...
Need help?
General
