What to do if my Hitachi CP-X608 Projector power does not come on?
If your Hitachi Projector isn't powering on, first ensure the electrical power cord is properly plugged in. Next, check that the power switch is set to the 'On' position. If there was a power interruption, turn the projector off, allow it to cool for at least 2 minutes, and then turn it back on.
What to do if the lamp does not light on my Hitachi CP-X608 Projector?
Please turn the power off, and allow the Hitachi Projector to cool down at least 20 minutes. After the projector has cooled down, check for any blockage of the air passage and if the air filter is dirty, and ensure the surrounding temperature doesn't exceed 35°C. If the same indication is displayed after the remedy, please change the lamp.
What to do if Hitachi CP-X608 Projector says 'CHECK THE AIR FLOW'?
If your Hitachi Projector displays 'CHECK THE AIR FLOW', it means the internal temperature is rising. Turn the power off and let the projector cool down for at least 15 minutes. Then, check if the air passage is blocked, if the air filter is dirty, or if the surrounding temperature is above 35°C. After addressing these issues, turn the power back on. If the message persists, set the FAN SPEED in the SERVICE menu's OPTION to HIGH.
What to do if my Hitachi CP-X608 shows a filter maintenance reminder?
If your Hitachi Projector reminds you about filter maintenance, immediately turn the power off. Clean or change the air filter. After cleaning or changing the filter, reset the filter timer.
What to do if my Hitachi CP-X608 Projector says 'CHECK THE AIR FLOW'?
If the Hitachi Projector displays 'CHECK THE AIR FLOW', it means the internal temperature is rising. Turn the power off and let the projector cool down for at least 15 minutes. Then, check if there's any blockage of the air passage, if the air filter is dirty, or if the surrounding temperature is above 35°C. After addressing these issues, turn the power back on. If the problem persists, set the FAN SPEED in the SERVICE item of the OPTION menu to HIGH.
What to do if my Hitachi CP-X608 Projector displays a filter check reminder?
If your Hitachi Projector shows 'REMINDER *** HRS PASSED AFTER THE LAST FILTER CHECK', immediately turn off the power. Clean or change the air filter. After cleaning or changing the filter, make sure to reset the filter timer.
What to do if my Hitachi Projector shows 'NO INPUT IS DETECTED'?
If your Hitachi Projector displays 'NO INPUT IS DETECTED', confirm the signal input connection and the status of the signal source.
Why does my Hitachi CP-X608 Projector say 'SYNC IS OUT OF RANGE'?
If your Hitachi Projector displays 'SYNC IS OUT OF RANGE', confirm the specs for your projector or the signal source.
How to restore sound on a Hitachi Projector?
If sound isn't coming from your Hitachi Projector, ensure the audio cables are correctly connected. If the MUTE function is enabled, restore the sound by pressing the MUTE or VOLUME button on the remote control. Also, check that the volume isn't set too low, and verify the AUDIO settings in the menu.
What does 'Check the air flow' mean on my Hitachi Projector?
The 'Check the air flow' message on your Hitachi Projector indicates that the internal temperature is rising. Turn the power off and let the projector cool down for at least 15 minutes. Then, check for any blockage of the air passage, inspect the air filter for dirt, and ensure the surrounding temperature doesn't exceed 35°C. If the problem persists, set the FAN SPEED in the OPTION menu to HIGH.
General| Resolution | XGA (1024 x 768) |
|---|---|
| Contrast Ratio | 500:1 |
| Lamp Life | 2000 hours (normal mode), 3000 hours (eco mode) |
| Display Type | LCD |
| Throw Ratio | 1.5 - 1.8:1 |
| Screen Size | 30 - 300 inches |
| Zoom Ratio | 1.2x |
| Brightness | 4000 ANSI Lumens |
| Input Ports | S-Video, Composite Video |
| Audio Output | 1W Mono |
| Lamp Type | UHB |
| Output Connectors | D-sub 15 pin x 1 |
| Noise Level | 35 dB (normal mode) |
| Power Consumption | 310W (Normal mode), 250W (Eco mode) |
To Next Page
