NOITCNUF OFNI
● By pressing (INFO) button, temperature around remote controller and monthly power consumption will
be displayed on the remote controller.
● After changing the batteries, direct the remote controller towards the indoor unit and press
(INFO) button.
Current calendar and clock will be transmitted from indoor unit.
● In order to receive information from indoor unit, the distance between remote controller and receiver of indoor
units is within 2 meters.
■ To check temperature around remote controller
■ Current calendar and clock can be retrieved from indoor unit
■ To check monthly power consumption
Press (INFO) button.
Temperature will be displayed for 10 seconds.
Direct the remote controller towards the receiver of indoor unit (within 2 meters
in front of indoor unit) and press (INFO) button. Wait for 2 seconds for
signal transmission.
Once received the current calendar and clock, check whether they are correct
or not by pressing (CLOCK) button.
● If there is no power supply to indoor unit or calendar and clock have not been
set, INFO function cannot be used for sending or receiving information.
Direct the remote controller towards the receiver of indoor unit (within 2 meters
in front of indoor unit) and press
(INFO) button. Wait for 2 seconds for
signal transmission.
While temperature around remote controller is displayed, press
(INFO)
button repeatedly. The display will show as below:
this month power consumption amount for heating
last month power consumption
amount for heating this month power consumption amount for cooling last
month power consumption amount for cooling temperature around remote
controller this month power consumption amount for heating ...... cyclically.
● If indication is not given, bring remote controller closer to the receiver of
the indoor unit.
● Indicated value shall be regarded as a guide only.
NOTE
● In case failure occurs to the air conditioner, by pressing (INFO) button, an error code will be displayed.
Direct the remote controller towards the receiver of indoor unit (within 2 meters in front of indoor unit)
and press (INFO) button. Wait for 2 seconds for signal transmission.
An error code will be displayed.
Call service center and inform the error code.
● Info Function to check monthly power consumption.
During installation, in case of power failure or breaker ON / OFF, ensure to set the clock and calendar for indoor
unit (unit in standby mode or auto restart), by pressing
(START / STOP) button.
Failure to do the above,monthly power consumption amount will not be displayed on the remote controller.
1
KCOL EDOM NOITAREPO
The remote controller can be set to fix the HEATING mode (including FAN), COOLING mode (including FAN)
and DEHUMIDIFYING mode (including FAN) operations.
■ Method to lock HEATING mode (including FAN) operation.
Press (ECO) and (POWERFUL) buttons simultaneously for about 5 seconds
when the remote controller is OFF.
“ ”, “ ” and “ ” will be displayed for about 10 seconds. Later, “ ” and “ ”
will remain.
This indicates that HEATING mode operation is locked.
When pressing (MODE) button, “ ”, “ ” or “ ” will be displayed.
■ Method to unlock HEATING mode (including FAN) operation.
Press
(ECO) and (POWERFUL) buttons simultaneously for about 5 seconds
when the remote controller is OFF.
All operation mode symbols will appear on the display for about 10 seconds. After
that, operation mode symbol before cancellation will be displayed.
This indicates that HEATING mode operation is unlocked.
■ Method to lock COOLING and DEHUMIDIFYING modes (including FAN)
operations.
Press (ECO) and (LIGHT ON /OFF) buttons simultaneously for about 5
“
”, “ ”, “ ” and “ ” will be displayed for about 10 seconds. Later, “ ” and
“ ” will remain.
This indicates that COOLING and DEHUMIDIFYING mode operation is locked.
When pressing (MODE) button, “ ”, “
”, “ ” or “ ” will be
displayed.
■ Method to unlock COOLING and DEHUMIDIFYING modes (including FAN)
operations.
Press (ECO) and (LIGHT ON /OFF) buttons simultaneously for about 5
All operation mode symbols will appear on the display for about 10 seconds. After
that, operation mode symbol before cancellation will be displayed.
This indicates that COOLING and DEHUMIDIFYING modes operation is unlocked.
NOTE
● Operation Mode Lock function will not activate if TIMER reservations activate.
TIMER reservations shall be deactivated first. Then, Operation Mode Lock function can be activated.
● HEATING, COOLING and DEHUMIDIFYING mode (including FAN) operations can be unlocked by pressing
the (RESET) button. However, by pressing the (RESET) button, all the information stored
in the remote controller will disappear. You may need to set the necessary information again.
seconds when the remote controller is OFF.
seconds when the remote controller is OFF.
To Next Page
Loading...
