Ta ble 3 External temperature category
External
temperature
Pattern Control sequence
Ta ble 6 Control pattern for the outdoor unit
State
transition
Ta ble 8 Relative values from the temperature setting
External temperature
≧32℃
Room temperature category
When the room
temperature rises
When the room
temperature declines
(when shifted from
category 3)
Ta ble 2 Room temperature category
(during operation)
When the room
temperature declines
(when shifted from
category 4)
Temperature setting
Room temperature
(relative value from the
temperature setting)
Room
temperature
category
Ta ble 1 Room temperature category
(at the time of operation startup)
Room temperature
(relative value from the
temperature setting)
When the external
temperature rises
When the external
temperature declines
Latch-type
reversing valve
Room two-
way valve
Fully
open
Category 4
Category 3
Category 2
Category 1
Compressor speed
Ta ble 4 Control by room temperature category
Cooling
position
Cooling
position
Fully closed
Stop
Fully
closed
Cooling position
Room
temperature
category
Ta ble 7 Stop times in a state transition of the
operation status
3 minutes
3 minutes
None
None
Compressor
stop time
State transition
Weak cooling ⇒ heating dry
Heating dry ⇔ cooling dry
Cooling dry ⇒ weak cooling
Heating dry ⇒ weak cooling
External temperature category
９０″
３′
１′
１１０″
３０″３０″
９０″
３０″
１′
９０″
ａ℃
ｂ℃
１℃
０．６６℃
１℃
Room temperature
１０″
３０″１０″
Open
Temperature judgment
Room temperature category
ＣＯＬＤＲＹ
ＣＯＬＤＲＹ
Operation status
Dry cool
Operation lamp
ＳＴＡＲＣＰＬ
DMIN
ＷＡＭＤＲＹ１・２・３
ＷＡＭＤＲＹ１・２・３
ＷＡＭＤＲＹ１・２・３
ＣO LM AX -COLMIN
ＲＹＳＴＯＰ１
STPSPTM1・2・3
４′
Ｔ１
４′
Ｔ２
＋0.66℃
−1.0℃
＋a℃
＋b℃
29℃
27℃
20℃
18℃
10℃
8℃
H
G
F
H
C
C
B
B
A
A
C
C
−
−
−
−
Lo
SS1
SS7
SS2
A
SS1
SS3
B
C
D
E
F
G
H
I
J
SS3
SS4
SS5
SS6
ａ
ｂ
External temperature
＜32℃
ＲＹＣＬＣＨＫ１
ＲＹＣＤＣＨＫ１
ＲＹＣＬＣＨＫ２
ＲＹＣＤＣＨＫ２
"Sensitive to heat" operation
Ta ble 9 Temperature settings for "Sensitive to heat"
and "Sensitive to cold" operations
Te mperature setting−１℃
"Sensitive to cold" operation Temperature setting＋１℃
COLDRY
ＷＡＭＤＲＹ３
ＷＡＭＤＲＹ２
ＷＡＭＤＲＹ１
COLMAX
COLMIN
Te mperature setting in
comfortable cooling
(remote control temperature
setting + SHIDD)
START/STOP switch
LOW
SILENT
MED
HI
Indoor unit
Outdoor unit
Room two-way valve
Latch-type reversing valve
Compressor speed
High humidity
High humidity
Low
humidity
Heating dry Heating dry Heating dry
Category 1(Stop)
Category 2 Category 4
fan speed set to AUTO
Category 3
Cooling dry
Weak cooling
Category 2
3' minimum
Notes:
(1) The product determines the room temperature category and external temperature category as shown in Tables 1, 2 and 3 according to the room temperature and
external temperature, and performs control as shown in Tables 4 and 5.
(2) For the outdoor unit, its operation pattern is controlled as shown in Table 6 according to the room temperature category and external temperature category.
(3) If the operation status shown in Table 5 makes a state transition depending on the changes in room temperature or external temperature, the product will perform cycle
balancing with a compressor stop time as shown in Table 7.
(4) When the temperature judgment is low humidity in room temperature category 2, the product will be stopped. (The compressor stop time at that time is 3 minutes
or more.)
(5) The room temperature setting in comfortable cooling must be the external temperature less 5 ℃. Provided that, if the temperature is higher than the room temperature,
the temperature setting must be set to room temperature, with 24 ℃ as the lower limit. The fan speed is set to MED.
(6) The humidity setting in dry cool must be 50% when the room temperature setting is 27 ℃ or more, 55% when it is 26 ℃ or more, and 60% when it is
25 ℃ or more.
(7) If the product is stopped in "heating dry" or "cooling dry", the outdoor unit will run for 30 seconds with the outdoor unit pattern J.
Category 4
Category 4
Category 3
Category 2 Category 2
Category 1
(stop)
Category 1
(stop)
Category 4
Category 3
Category 2
Category 1
The outdoor unit patterns I and J are used for correction.
External temperature
category
Operation status
Operation status
Outdoor unit
control pattern
Outdoor unit
control pattern
Outdoor unit
control pattern
Outdoor unit
control pattern
Weak
cooling
Weak
cooling
Weak
cooling
Weak
cooling
Stop Stop Stop Stop
Cooling
dry
Cooling
dry
Cooling
dry
Cooling
dry
Cooling
dry
Heating dry Heating dry Heating dry
Ta ble 5 Outdoor unit control (initial values) according to the room
temperature and external temperature
Category 4
Category 3
Category 2
Category 1
Room
temperature category
Category 4Category 3Category 2Category 1
Operation status
Operation status
−RYSTOP1 ℃
−RYSTOP 1℃
(T1=GFSTM1,T2=GFSTM2)
– 73 –
To Next Page
Loading...
