HK Audio Cadis CAD 208 User Manual

Cadis™ Manual 1.0
Table of Contents :
A CADIS™ Speaker Cabinets .................................................................... 5
1 CAD 208 Mid/High Enclosure ............................................................... 5
1.1 Technical Data, CAD 208 ....................................................................... 5
2 CAD 115 Sub Subwoofer ........................................................................6
2.1 Technical Data, CAD 115 Sub ..................................................................6
B CADIS™ Transport Solution .................................................................. 7
1 CADIS 208 Mid/High Cases .................................................................. 7
1.1 Dimensions and Weights of CAD 208 Cases .......................................... 7
2 CAD 115 Sub Dolly ................................................................................. 7
C Rigging the CADIS™ System .................................................................8
1 Use ........................................................................................................ 8
1.1 Intended Use ......................................................................................... 8
1.2 Misuse ...................................................................................................8
2 Warranty and Liability ............................................................................ 8
2.1 Responsibilities of the Operator ............................................................ 8
2.2 Storage, Maintenance, Inspection and Repair
of CADIS™ Rigging Hardware ...............................................................8
2.3 Technical Specifications of CADIS™ Rigging Hardware .........................9
2.4 Maximum Number of Flown CAD 208 Mid/High Enclosures ................9
2.5 Maximum Number of Flown CADIS™ CAD 115 Subs .............................9
2.6 Pick-points for Flying CADIS™ Enclosures ............................................9
2.7 Structural Modifications of CADIS™ Rigging Hardware ........................9
2.8 Original HK AUDIO Accessories: ...........................................................9
2.9 Initiation and Operation ...................................................................... 10
3 Flown Applications and Components of CADIS™ Rigging Hardware... 10
4 Adjusting the Set angle Between Two CAD 208 Enclosures ..................11
4.1 Compression Mode ..............................................................................11
4.2 Fixed Mode ...........................................................................................13
5 Flying CAD 115 Subwoofers ...................................................................13
5.1 Components .........................................................................................13
5.2 As an Independent Bass Array on a Second Rigging Frame ..................14
5.3 In Combination with CAD 208 Mid/High Enclosures ...........................14
5.4 With a Standard Rigging Frame ............................................................14
5.5 With CAD 115 Subwoofers .....................................................................14
5.6 Connecting Speaker Cords ....................................................................15
5.7 Checking Individual Mid/High Enclosures ...........................................15
5.8 Configuring the Controller Network Using Audio Controller Software ..15
6 Tearing Down and Transporting the System ..........................................15
D CADIS™ Aiming Software Setups with EASE Focus ........................... 16
E Controlling CADIS™ ........................................................................... 16
F Controllers and Controller Software .....................................................17
G Service .................................................................................................25
1 CADIS™ Replacement Parts .................................................................25
2 A Look at the Required Tools ................................................................25
3 Replacing Loudspeakers and Voice Coils ..............................................25
3.1 8” Woofers ........................................................................................... 26
3.2 The 1” Drivers’ Voice Coils ...................................................................26
H Appendix/Reference Library ................................................................ 27
1 CADIS™ FIRNET Controller Filter Sets ................................................ 27
Index of Figures:
Fig. 1: CAD 208 ........................................................................................ 5
Fig. 2: Subwoofer CAD 115 Sub ................................................................6
Fig. 3: CAD 208 case and CAD 115 dolly ................................................... 7
Fig. 4: 12 flown CAD 208 mid/high enclosures ...................................... 10
Fig. 5: CAD 208 mid/high enclosure with integrated rigging hardware .. 10
Fig. 6: CADIS™ standard rigging frame ................................................. 10
Fig. 7: CADIS™ connector frame ............................................................ 10
Fig. 8: CADIS™ wall mount, ceiling mount ............................................ 10
Fig. 9: Shackles for attaching motors, straps ......................................... 10
Fig. 10: Lashing strap for curving the array in compression mode ............11
Fig. 11: Quick-release pin .........................................................................11
Fig. 12: The CAD 208’s set angle in compression mode 4.5° ....................11
Fig. 13: Rigging frame at 0° ......................................................................11
Fig. 14: Adjusting intermediate angles to curve the overall array ..............12
Fig. 15: Mounting the standard rigging frame ..........................................12
Fig. 16: Setting the angle to curve a CAD 208 array ..................................12
Fig. 17: Hoisting the top four CAD 208 enclosures ...................................12
Fig. 18: a, b, c: Rigging additional CAD 208 enclosures .......................12/13
Fig. 19: Attaching the lashing strap ..........................................................13
Fig. 20: Example of a fixed mode application with a 4.5° angle .................13
Fig. 21: CAD 115 Sub rigging kit ................................................................14
Fig. 22: CAD 115 Sub pick points ...............................................................14
Fig. 23: Ground stack with the standard rigging frame .............................14
Fig. 24: Ground stack with CAD 115 subwoofers .......................................14
Fig. 25: FirNet™ – Entering your PC’s IP address .....................................17
Fig. 26: FirNet™ – Opening the Update Scene + Filter Settings dialog ....18
Fig. 27: FirNet™ – Selecting filters and controllers .................................18
Fig. 28: FirNet™ – Opening the dialog box for loading individual filters ..18
Fig. 29: FirNet™ – Admin menu settings ..................................................18
Fig. 30: FirNet™ – Front ......................................................................... 19
Fig. 31: FirNet™ – Networked FIRNET and PC ........................................20
Fig. 32: FirNet™ – Networked hub and PC ..............................................20
Fig. 33: FirNet™ – Rear ............................................................................21
Fig. 34: Required service tools ..................................................................25
Fig. 35: CAD 208 with the grille removed .................................................26
Fig. 36: CAD 208 with the side panels detached ...................................... 26
Fig. 37: Dismantled CAD 208 baffle board with the woofer ..................... 26
Fig. 38: Voice coil removed from the CAD 208 HF driver ......................... 26
Index of Tables:
Table 1: Weights of CADIS™ mid/high enclosures .....................................9
Table 2: Weights of CADIS™ CAD 115 subwoofers ......................................9
Table 3: Set angle between the rigging frame and
the first mid/high enclosure .........................................................14
Table 4: Replacement parts list as of June 2009 ........................................25
Table 5: CADIS™ FIRNET filter sets as of June 2009 ................................ 27

HK Audio Cadis CAD 208 Specifications

General

Brand	HK Audio
Model	Cadis CAD 208
Category	Stereo System
Language	English