Hobart HS6 Service Manual

KNIFE MOTOR CONTINUITY TEST ............................................................... 44
AUTO MOTOR TEST (HS7 & HS9) .................................................................... 44
CONTROL BOARD TEST (HS6 & HS8) ................................................................ 45
CONTROL BOARD TEST (HS7 & HS9) ................................................................ 46
KEYPAD TEST (HS7 & HS9) .......................................................................... 48
SHARPENING ........................................................................................ 48
INTRODUCTION .................................................................................. 48
KNIFE SHARPENING ............................................................................. 48
QUALITY OF SLICE CHECKS ......................................................................... 49
INDEX SLIDE MECHANISM ADJUSTMENT ........................................................... 52
CARRIAGE TRAY INTERLOCK SWITCH 1S TEST (HS8 & HS9) ....................................... 52
OPERATIONAL CHECK ........................................................................... 52
CONTINUITY TEST (HS8) ......................................................................... 53
CONTINUITY TEST (HS9) ......................................................................... 53
LED CHECK (HS9) ................................................................................ 53
CARRIAGE TRAY INTERLOCK SWITCH 1S ADJUSTMENT (HS8 & HS9) .............................. 54
AUTO / MANUAL SWITCH 5S TEST (HS7 & HS9) ..................................................... 54
OPERATIONAL CHECK ........................................................................... 54
CONTINUITY TEST ............................................................................... 54
LED CHECK ...................................................................................... 55
AUTO / MANUAL SWITCH 5S ADJUSTMENT (HS7 & HS9) ............................................ 55
HOME SWITCH 3S TEST (HS7, HS8 & HS9) .......................................................... 55
OPERATIONAL CHECK ........................................................................... 55
CONTINUITY TEST (HS8) ......................................................................... 56
CONTINUITY TEST (HS7 & HS9) .................................................................. 56
LED CHECK (HS7 & HS9) ......................................................................... 56
HOME SWITCH 3S ADJUSTMENT (HS7, HS8 & HS9) ................................................. 57
POWER APPLIED ADJUSTMENT (HS7 & HS9) .................................................... 57
POWER NOT APPLIED ADJUSTMENT (HS7, HS8 & HS9) ......................................... 57
KNIFE RESET SWITCH 4S TEST (HS8 & HS9) ........................................................ 58
OPERATIONAL CHECK (HS8 & HS9) ............................................................. 58
CONTINUITY TEST (HS8) ......................................................................... 58
CONTINUITY TEST (HS9) ......................................................................... 58
LED CHECK (HS9) ................................................................................ 58
KNIFE RESET SWITCH 4S ADJUSTMENT (HS8 & HS9) ............................................... 59
POWER APPLIED TEST (HS9) .................................................................... 59
POWER NOT APPLIED TEST (HS8 & HS9) ....................................................... 60
GAUGE PLATE CLOSED SWITCH 2S TEST (HS8 & HS9) ............................................. 60
OPERATIONAL CHECK ........................................................................... 60
CONTINUITY TEST (HS8) ......................................................................... 61
CONTINUITY TEST (HS9) ......................................................................... 61
LED CHECK (HS9) ................................................................................ 62
GAUGE PLATE CLOSED TO STOP SWITCH 2S ADJUSTMENT (HS8 & HS9) ......................... 62
GAUGE PLATE ADJUSTMENT ........................................................................ 63
INTRODUCTION .................................................................................. 63
GAUGE PLATE FACTORY DEFAULT SETTING ................................................... 64
GAUGE PLATE WARP CHECK .................................................................... 64
GAUGE PLATE PARALLELISM TO KNIFE - CHECK ............................................... 64
GAUGE PLATE PARALLELISM TO KNIFE - ADJUSTMENT ........................................ 65
GAUGE PLATE TO KNIFE GAP - CHECK ......................................................... 65
GAUGE PLATE TO KNIFE GAP - ADJUSTMENT .................................................. 65
GAUGE PLATE TO KNIFE ANGLE - CHECK ...................................................... 65
GAUGE PLATE TO KNIFE ANGLE - ADJUSTMENT ............................................... 66
ZERO ADJUST - CHECK .......................................................................... 66
ZERO ADJUST - ADJUSTMENT ................................................................... 66
ELECTRICAL OPERATION ................................................................................ 68
COMPONENT FUNCTION ............................................................................ 68
COMPONENT LOCATION ............................................................................. 69
HS Series Slicer
F45476 Rev. A (0313) Page 4 of 85

Hobart HS6 Specifications

General

Brand	Hobart
Model	HS6
Category	Kitchen Appliances
Language	English