Need help?Do you have a question about the Holman dial ezy 4 and is the answer not in the manual?
Explains the concept of programs grouping stations and outlines the 3 essential steps for setting up watering schedules.
Details manual program/station runs, winter suspension, and the system test facility for checking valves and sprinklers.
Provides tips for easier programming and an illustrative example for an 8-station controller setup.
Guides on setting the current time, AM/PM, and the correct day of the week for accurate operation.
Instructions for setting the calendar, specifically for Odd/Even day watering restrictions.
Details on setting up to four watering start times per program, including adjusting hours and minutes.
Covers interval watering (daily to 15th day) and individual day selection (on/off for each day of the week).
Explains how to enable Odd or Even day watering based on regional restrictions and house numbers.
Describes how to set the duration for each station's watering cycle, from minutes to hours, or turn it off.
Allows manual activation of a single station for a specified duration, up to 12 hours 59 minutes.
Tests all stations sequentially for 2 minutes each to verify valve and sprinkler operation.
Enables manual execution of a complete program as set in the automatic schedule.
Instructions on how to halt automatic or manual watering cycles by turning the dial to the 'Off' position.
Explains how the controller manages multiple start times set for the same program, sequencing them.
Details the default program that runs during power outages or when the battery is not fitted.
Allows delaying automatic watering schedules for a specified period in 24-hour increments.
Disables automatic watering cycles during winter or periods of rain without erasing programmed data.
Enables adjustment of station run times by percentages to save water based on seasonal changes.
Guidance on securely mounting the indoor controller unit in a suitable location near a power outlet.
Crucial warnings and instructions for safe electrical connections, adhering to codes and disconnecting power.
Preparation steps for wires, stripping insulation, and connecting them securely to the terminal block.
Details the layout of the terminal block, including connections for AC, Pump, and individual stations (1-8).
Instructions for connecting the 24VAC plug pack transformer, advising on suitable power sources.
Guidance on wiring up to two 24VAC solenoid valves per station output back to the common terminal.
Instructions for systems using a pump, including relay connections and wiring unused stations.
Details the mains supply requirements, specifying the 24VAC 50Hz @ 1 Amp plugpack transformer.
Notes that the Plug Pack Model is specifically designed and suitable only for indoor installations.
Lists input voltage, maximum output current, and specific ratings for solenoid valves and pump/master valve.
Explains the concept of programs grouping stations and outlines the 3 essential steps for setting up watering schedules.
Details manual program/station runs, winter suspension, and the system test facility for checking valves and sprinklers.
Provides tips for easier programming and an illustrative example for an 8-station controller setup.
Guides on setting the current time, AM/PM, and the correct day of the week for accurate operation.
Instructions for setting the calendar, specifically for Odd/Even day watering restrictions.
Details on setting up to four watering start times per program, including adjusting hours and minutes.
Covers interval watering (daily to 15th day) and individual day selection (on/off for each day of the week).
Explains how to enable Odd or Even day watering based on regional restrictions and house numbers.
Describes how to set the duration for each station's watering cycle, from minutes to hours, or turn it off.
Allows manual activation of a single station for a specified duration, up to 12 hours 59 minutes.
Tests all stations sequentially for 2 minutes each to verify valve and sprinkler operation.
Enables manual execution of a complete program as set in the automatic schedule.
Instructions on how to halt automatic or manual watering cycles by turning the dial to the 'Off' position.
Explains how the controller manages multiple start times set for the same program, sequencing them.
Details the default program that runs during power outages or when the battery is not fitted.
Allows delaying automatic watering schedules for a specified period in 24-hour increments.
Disables automatic watering cycles during winter or periods of rain without erasing programmed data.
Enables adjustment of station run times by percentages to save water based on seasonal changes.
Guidance on securely mounting the indoor controller unit in a suitable location near a power outlet.
Crucial warnings and instructions for safe electrical connections, adhering to codes and disconnecting power.
Preparation steps for wires, stripping insulation, and connecting them securely to the terminal block.
Details the layout of the terminal block, including connections for AC, Pump, and individual stations (1-8).
Instructions for connecting the 24VAC plug pack transformer, advising on suitable power sources.
Guidance on wiring up to two 24VAC solenoid valves per station output back to the common terminal.
Instructions for systems using a pump, including relay connections and wiring unused stations.
Details the mains supply requirements, specifying the 24VAC 50Hz @ 1 Amp plugpack transformer.
Notes that the Plug Pack Model is specifically designed and suitable only for indoor installations.
Lists input voltage, maximum output current, and specific ratings for solenoid valves and pump/master valve.
General| Brand | Holman |
|---|---|
| Model | dial ezy 4 |
| Category | Lawn and Garden Equipment |
| Language | English |
To Next Page
