Honeywell 40014 - User Manual

Available at www.HoneywellStore.com
CEILING FAN AND LIGHT WALL CONTROL
Model 40014 / Item # 0374121
User Guide
IMPORTANT SAFETY INSTRUCTIONS S S

1. Readandkeepthisinstructionsheetforfuturereference.
2. Pleasenotethatallfixedwiringappliancesshouldbeinstalledbyaqualified
electrician.
3. Thesupplytothereceivershouldbeconnectedonitsowncircuit.
4. Switchoffthepoweratthecircuitbreakerbeforeworkingon
receiverorceilingfan.
5. Thisunitistobeusedforthecontrolofaceilingfananditselectricalsourcemust
beAC110/120V,60Hz.
6. Donotinstallindamplocationorimmerseintowater.Forindooruseonly.
7. Donotusethisremotewithfansthat
havepre‐installedremotecontrols.

CAUTION: To reduce the risk of fire or injury, do not use this product in
conjunction with any variable (rheostat) wall control.
RECEIVER INSTALLATION INSTRUCTIONS S- 

NOTE:Thisremotecanworkwithavarietyofhuggerfantypes,however,thereis
typicallyverylittlespaceinthehangerbracketareatoinstallareceiver.Therefore,
wedonotrecommendusingthisremotewithhuggertypeor5speedceilingfans.

1. Afterswitchingpoweroff@
circuitbreaker,removeceilingfancanopyfromthe
mountingbracket.Disconnectexistingwiringbetweenceilingfanandsupplyat
electricaljunctionbox.
2. SlidethereceiverintothemountingbracketperFIG.1beingcarefulnot
topinchtheantennawire.
3. Thereceiverwillbeinsertedbetweenthedownrod
andthemountingbracket.
4. MakewiringconnectionsperFIG.2. 
5. Pushallconnectedwiresbackintothejunctionboxandreinstallthecanopyonto
themountingbracket.
6. ManuallysetfanspeedcontroltoHIGHandsetlighttoONusingthepullchains.

NOTE:Fortheremote
tofunctionproperly,thefanmustbeonHIGHspeedand
lightsmustbeONtouse.

CAUTION: Incorrect wire connection can damage this receiver and could
cause injury or fire.

ACTIVATING THE LEARNING PROCESS (SMART SYNC) S
      

NOTE:Thisremoteispre‐programmedfromthefactoryandshouldworkrightoutof
theboxoncethebatteryisinstalled.Should,foranyreason,re‐programmingbe
neededpleasefollowthelearningprocessasfollows:

1. Afterinstallationiscompleteandpoweristurnedon,pressandhold
the“FANOFF”
buttonfor3seconds.Fanwillturnonathighspeedandlight(ifinstalled)blinks3
times.ThisconfirmsthattheSMARTSYNCsettingisactive.Younowhave30seconds
topresstheFANOFFkey.TaptheFANOFFbuttonagaintoturnoff
thefan.
2. Ifusercannotfinishthesettingwithinthe30secondstimeframethemainpower
mustbeturnedoffandre‐startedagain.Thiswillresettheunit.Repeatstep1until
theLEARNINGfeatureisactivatedasindicated.

NOTE:Usermustpress“FANOFF”keywithin
30secondsaftermainpoweristurne d
on.









 
FANCANOPY
MOUNTING
BRACKET
FIG1

INSERTING RECEIVER
INTO CANOPY ASSEMBLY
 
WALL CONTROL LIVE (BLACK)
NEUTRAL (WHITE)
A
NTENN
A
LIGHT
(BLUE)
MOTOR
(BLACK)
MOTOR
(WHITE)
FIG2
CONNECTINGTHERECEIVER
TOTHEFAN

Honeywell 40014 Specifications

General

Brand	Honeywell
Model	40014
Category	Controller
Language	English

Summary

Important Safety Instructions

Receiver Installation Instructions

Activating the Learning Process (Smart Sync)

Wall Control Operation

High; Medium; Low Speed

Controls fan speed by tapping buttons for high, medium, or low respectively.

Fan Off

Tap lightly to turn the fan off.

Light

Tap lightly to turn the light on or off.

Walk Away Light Delay

Tap once to turn off light and fan after 1 minute.

Home Shield

Press and hold buttons for 3 seconds to activate security mode.

Wall Control Installation Instructions

Trouble Shooting

Warranty

Federal Communications Commission Interference Statement