REPLACING THE BATTERY
The LED will not flash during transmission if the battery is low.
Replace the battery as follows.
1. Remove the screw from the case back, then remove the
case back.
2. Insert the blade of a small screwdriver under the battery as
shown.
3. Twist the screwdriver to release the battery.
4. With the Positive (+) end of a new battery facing UP, insert
the battery as shown, sliding it under the gold tab, then
pressing down to snap into place.
IMPORTANT: Positive (+) end must face up.
Use Maxell CR2032, Duracell DL2032,
or SENER CR2032
lithium battery only.
5. Replace the case back and replace the screw to secure the
case.
!
• Improper installation will result in damage to the battery.
• Do not remove the printed circuit board.
Failure of Replaceable Batteries
This wireless key has been designed to provide several years
of battery life under normal conditions. The expected battery
life is a function of the device environment, usage and type.
Ambient conditions such as high humidity, high or low
temperatures, or large temperature fluctuations may reduce
the expected battery life.
This device will report a low battery condition to the control
panel as a trouble condition, when the batteries need to be
replaced. In addition the LED will not flash when a button is
pressed. However, if the device is unused for a long period of
time, it may fail to operate as expected. Regular testing and
maintenance will keep the system in good operating condition
for the lifetime of the product.
IMPORTANT! This wireless key is intended as a convenience to the
user and should not be considered as a life safety device. If life safety is
important, please select a supervised wireless key (e.g. type 5802MN).
SPECIFICATIONS
Unit Dimensions: 2.25" x 1.25" x 0.5" (57mm x 31.75mm x 12.7mm)
Battery: 3V, 210mAh, Maxell CR2032, Duracell DL2032, or
SENER CR2032
IC MODEL No. 5834
WARRANTY INFORMATION
For the latest warranty information, please go to:
http://www.security.honeywell.com/hsc/resources/wa/index.html
REFER TO THE INSTALLATION INSTRUCTIONS FOR
THE CONTROL WITH WHICH THIS DEVICE IS USED
FOR LIMITATIONS OF THE ENTIRE ALARM SYSTEM.
5834-004-V0
GOLD
TA B
BATTERY
TO REMOVE, SLIDE
SCREWDRIVER BLADE
UNDER BATTERY HERE
Removing the Battery
5834-005-V0
INSTALL WITH POSITIVE (+)
SIDE UP. SLIP BATTERY
UNDER GOLD TAB THEN
PRESS DOWN
IMPORTANT
POSITIVE (+)
SIDE MUST
FACE UP
BATTERY
INSTALL UNDER GOLD TAB
BATTERY
THEN PRESS DOWN
Installing the Battery
FEDERAL COMMUNICATIONS COMMISSION
STATEMENTS:
The user shall not make any changes or modifications to
the equipment unless authorized by the installation
Instructions or User's Manual. Unauthorized changes or
modifications could void the user's authority to operate the
equipment.
FCC NOTICE
This device complies with Part 15 of FCC Rules, and RSS
210 of IC. Operation is subject to the following two
conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any
interference received, including interference that may
cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la
FCC & de RSS 210 des industries Canada. Son
fonctionnement est soumis aux conditions suivantes: (1)
Cet appareil ne doit pas causer d'interferences nuisibles.
(2) Cet appareil doit accepter toute interference reçue y
compris les interferences causant une reception
indesirable.
IMPORTANT SECURITY NOTICE
Please inform the User about the security importance of their
key fob, and what to do if it is lost.
Explain that the key fob is similar to their keys or access
card. If lost or stolen, another person can compromise their
security system. They should immediately notify the
Dealer/Installer of a lost or stolen key fob. The
Dealer/Installer will then remove the key fob programming
from the security system.
Ê800-07457bŠ
800-07457 9/10 Rev. D
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Copyright © 2010 Honeywell International Inc.
www.honeywell.com/security
To Previous Page
Loading...
Need help?
General
