800-03612 1/09 Rev. B
ADEMCO
ADEMCO ADEMCO
ADEMCO 6460S
6460S6460S
6460S/6460
/6460
/6460
/6460
REMOTE KEYPAD
REMOTE KEYPADREMOTE KEYPAD
REMOTE KEYPAD
INSTALLATION AND SETUP GUIDE
GENERAL INFORMATION
The ADEMCO 6460S (silver) and 6460W (white) are
addressable Remote Keypads designed for use with
Honeywell's ADEMCO series control panels. Addresses are
set via the keypad keys.
The keys on the keypad are continuously backlit for
convenience.
NOTE: If supported, the ADEMCO 6460S and 6460W
keypads are supervised by control panel. Supervision must
be enabled for commercial fire installations.
KEYPAD DISPLAYS AND LEDS
The ADEMCO 6460S and 6460W keypads have the
following display features:
• 2-line Alpha Display
• Custom Zone Descriptors
• Built-in Speaker Sounder
• Dedicated Function Keys
• Backlit Display (permanent display backlighting is
an option on some controls; see the control's
instructions for details).
The following table shows the LEDs and their functions:
LED Function
Red Lights when the system is armed in any mode
Green Lights when the system is "ready" to be armed.
SPECIAL FUNCTION KEYS
The keypads also feature function keys. These keys may be
programmed for panic alarms or other special functions
such as macros. See the control's instructions for details.
Function keys must be held down for at least 2
seconds to activate an alarm; key pairs are activated
immediately.
Function Keys
A or [1] and [✻]
B or [✻] and [#]
C or [3] and [#]
D
WIRING AND INSTALLATION
The keypads can be surface mounted directly to a drywall,
or to a single- or double-gang electrical box.
1. Push the two case release snaps at the bottom of the
keypad with the blade of a medium screwdriver (this will
push in the release snap), then pull that side of the case
back away. Refer to Figure 1 for location of the case back
release snaps.
2. Route wiring from the control panel through the opening
in the case back.
3. Mount the case back to a wall or electrical box.
4. Wire directly from the keypad’s terminal block to the
terminal block on the control panel. (See Wiring Table
below).
NOTE: No more than one wire per terminal may be
connected. If daisy-chained configuration is required,
pig-tail wires together so that only one wire is
terminated under the screw. Use 16-24 AWG wire only!
Wiring Table
Keypad Control Panel Wire Color
▲G
Data In Green
– – Aux Pwr (GND) Black
+ + Aux. Pwr Red
▼Y
Data Out Yellow
See the control panel’s Installation and Setup Guide for
more complete details.
5. Reattach the keypad to its case back.
JKL
AWAY
CODE
ARMED
READY
S
T
A
Y
O
F
F
M
A
X
D
I
N
S
E
N
I
G
H
R
S
P
Q
T
T
A
N
R
E
A
D
Y
B
Y
P
A
S
S
C
H
I
M
E
TEST
4
6
TUV
9
0
N
O
M
X
Z
Y
W
U
M
N
E
F
D
ABC
3
5
8
2
1
7
*
#
NOTE:
TO REMOVE CASE BACK
PUSH IN THE TWO RELEASE
SNAPS LOCATED ALONG THE
BOTTOM OF THE KEYPAD
AND LIFT UP.
6460S-001-V1
RELEASE
SNAPS
DCBA
Figure 1. Removing the Case Back
WWW.DIYALARMFORUM.COM
WWW.DIYALARMFORUM.COM
To Next Page
Need help?
Display
Power
Weight and Dimensions
