Honeywell CENTRALINE CLCM6T21N User Manual

CLCM1H,6H,6T
Digital Wall Modules
Installation Instructions
Copyright © 2016 Honeywell GmbH ● All Rights Reserved MU1Z-0902GE51 R0416C
FUNCTIONAL OVERVIEW
Table 1. Functional overview
model
sensor
suitable controllers
CLCM1H112
temp. / humidity
PANTHER
CLCM6H212
temp. / humidity
PANTHER
CLCM6T21N
temperature
PANTHER + SERVAL
BEFORE INSTALLATION
All wiring must comply with local electrical codes and
ordinances or as specified on installation wiring diagrams.
Digital Wall Module (DWM) wiring can be sized from 1.5 to
0.34 mm
2
, depending on the application. The maximum
length of wire from a device to a DWM is 50 m. Twisted pair
wire is recommended for wire runs longer than 30.5 m.
CAUTION
EMI Noise Introduction. Risk of erratic system
operation.
Keep wiring at least 300 mm away from large induc-
tive loads such as motors, line starters, lighting
ballasts and large power distribution panels. During
installations, try to avoid areas of high EMI noise.
Run DWM wiring separately from 50 Vac or greater
power wiring.
WARNING / CAUTION
Risk of electric shock or equipment damage!
► Do not touch any live parts inside the DWM housing.
► Disconnect the power supply before making connections
to or removing connections from the DWM's terminals.
► Do not reconnect the power supply until you have com-
pleted the installation.
► If the DWM is powered via terminal 8 and connected to
earth ground, then the cable must be shielded.
► Observe precautions for handling electrostatic sensitive
devices.
Cover Disassembly/Assembly
The DWM comes packed with a sub-base that mounts
separately for ease of installation; to disassemble the cover
and the sub-base, see Fig. 1. When re-attaching, make sure
that the latch on the underside of the DWM engages
properly.
2
LIFT
1
PRESS
Fig. 1. Cover disassembly / assembly
INSTALLATION
NOTE: Maintain a mounting clearance of approx. 10 cm on
both sides of the DWM in order to allow a free airflow
for the temperature sensor and accessibility of the
setpoint dial.
Do not mount the DWM on an outside wall, on a wall
containing water pipes, or near air ducts. Avoid
locations exposed to discharge air from registers or
radiation from lights, appliances, or the sun.
The wall modules can be mounted on a 60-mm wall outlet
box using 3.5-mm screws or on a wall (see Fig. 2). When
mounting directly on a wall, use the type of screws
appropriate for the wall material.
See Fig. 5 for bore-holes and mounting dimensions
(dimensions are the same for all models).
screw
sub-base
screw
cover
Fig. 2. Mounting of DWM (CLCM6H,6T shown)

Honeywell CENTRALINE CLCM6T21N Specifications

General

Brand	Honeywell
Model	CENTRALINE CLCM6T21N
Category	Control Unit
Language	English

Summary

Functional Overview

Model and Controller Compatibility

Details DWM models, sensors, and compatible controllers for easy reference.

Installation Procedures

Pre-Installation Guidelines

Covers wiring, EMI, electrical safety, and ESD precautions before mounting the DWM.

Cover and Sub-base Handling

Instructions for disassembling and reassembling the DWM cover and sub-base.

DWM Mounting Requirements

Specifies mounting clearance, location considerations, and wall mounting methods.

Wiring and Power Connections

Wiring with PANTHER Controllers

Step-by-step guide for wiring DWM modules with PANTHER controllers, referencing terminal connections.

Wiring with SERVAL Controllers

Instructions for wiring DWM modules with SERVAL controllers, including terminal connections.

Low-Voltage Powering Precautions

Safety advice for powering DWM with 24 Vac, ensuring compliance with Class II restrictions.

DWM Configuration

Configuration Mode Entry

Steps to enter configuration mode using buttons and the setpoint dial.

Parameter Settings

Details on various DWM parameters (P1-P8) for setting temperature, display, and overrides.

Advanced Settings and Defaults

Remote Reset Functionality

Explanation of how to remotely reset wall module setpoint and fan speed overrides.

Setpoint and Humidity Limits

Configuration of setpoint limits (P9) and humidity output limits (PA).

Factory Defaults Reset

Procedure to reset all DWM settings to their factory default values.

Controller Configuration Mapping

Tables showing preferred DWM parameter configurations based on SERVAL and PANTHER software.