CPO-PC400-W/CPO-PC400-UW HVAC CONTROLLER
3 EN0B-0085 IE10 R0420
GENERAL SAFETY
INFORMATION
• When performing any work (installation, mounting,
start-up), all manufacturer instructions and in
particular the Installation and Commissioning
Instructions (EN1B-0077IE10) are to be observed.
• The ComfortPoint™ Open System (including the CPO-
PC400-W/CPO-PC400-UW HVAC Controller, Panel Bus
I/O modules, manual disconnect modules, and the
auxiliary terminal packages) may be installed and
mounted only by authorized and trained personnel.
• Rules regarding electrostatic discharge should be
followed.
• If the ComfortPoint™ Open System is modified in any
way, except by the manufacturer, all warranties
concerning operation and safety are invalidated.
• Make sure that the local standards and regulations are
observed at all times. Examples of such regulations are
VDE 0800 and VDE 0100 or EN 60204-1 for earth
grounding.
• Use only accessory equipment which comes from or has
been approved by Honeywell.
• It is recommended that devices be kept at room
temperature for at least 24 hours before applying power.
This is to allow any condensation resulting from low
shipping/storage temperatures to evaporate.
• The ComfortPoint™ Open System must be installed in a
manner (e.g., in a lockable cabinet) ensuring that
uncertified persons have no access to the terminals.
• Investigated according to United States Standard UL-
60730-1,UL-916, and UL60730-2-9.
• Investigated according to Canadian National
Standard(s) C22.2, No. 205-M1983 (CNL-listed).
• Do not open the CPO-PC400-W/CPO-PC400-UW, as it
contains no user-serviceable parts inside!
• CE declarations according to LVD Directive
2014/35/EU and EMC Directive 2014/30/EU.
• Product standards are EN 60730-1 and EN 60730-2-9.
• Transmitter Antenna (From Section 6.8 RSS-GEN, Issue
5, April 2018):
— This radio transmitter [IC: 24552-00001] has been
approved by Innovation, Science and Economic
Development Canada to operate with the antenna
types listed below, with the maximum permissible
gain indicated. Antenna types not included in this
list that have a gain greater than the maximum gain
indicated for any type listed are strictly prohibited
for use with this device.
— Le présent émetteur radio [IC: 24552-00001] a été
approuvé par Innovation, Sciences et Développe-
ment économique Canada pour fonctionner avec
les types d'antenne énumérés cidessous et ayant un
gain admissible maximal. Les types d'antenne non
inclus dans cette liste, et dont le gain est supérieur
au gain maximal indiqué pour tout type figurant sur
la liste, sont trictement interdits pour l'exploitation
de l'émetteur.
Professional Installation
• This device must be professionally installed, this should
be noted on grante.
• To maintain compliance, only the antenna types that
have been tested shall be used, which listed in Table 33,
“Antenna Part Numbers,” on page 39.
• This device requires a significant technology
engineering expertise towards understanding of the
tools and relevant technology, not readily available to
average consumer. Only a person professionally trained
in the technology is competent.
• This device is not directly marketed or sold to general
public.
Safety Information as per EN60730-1
The ComfortPoint™ Open System is intended for
residential, commercial, and light-industrial environments.
The ComfortPoint™ Open System is an independently
mounted electronic control system with fixed wiring.
The CPO-PC400-W/CPO-PC400-UW is suitable for
mounting in fuse boxes conforming with standard
DIN43880, and having a slot height of max. 45 mm.
It is suitable for panel rail mounting on 35 mm standard
panel rail (both horizontal and vertical rail mounting
possible).
The CPO-PC400-W/CPO-PC400-UW is used for the
purpose of building HVAC control and is suitable for use
only in non-safety controls for installation on or in
appliances.
Table 1. Safety Information as per EN60730-1
Electric Shock
Protection
PELV
Pollution Degree Pollution Degree 2, suitable for use
in industrial environments.
Installation Class 3
Overvoltage
Category
24 V-powered controls: Category I
Rated Impulse
Voltage
330 Vac for Category I (SELV)
Automatic
Action
Type 1.C (micro interruption for the
relay outputs)
Software Class Class A
Enclosure IP20 according to EN-60529
Ball-pressure
Test
Temperature
>75 °C for all housing and plastic
parts
>125 °C in the case of devices
applied with voltage-carrying parts,
connectors, and terminals.
Electromagnetic
Interference
Tested at 230 Vac, with the
modules in normal condition.
System
Transformer
Europe: safety isolating
transformers according to
IEC61558-2-6
U.S.A. and Canada: NEC Class-2
transformers
To Next Page
Loading...
