Honeywell HWTLMT508W - User Manual

Questions and Answers

T
Teresa WilkinsAug 10, 2025
Why is no water coming out of my Honeywell Water Dispenser?
- D
  delacruzshannonAug 10, 2025
  If no water is coming out of your Honeywell Water Dispenser, there could be several reasons. First, ensure the unit is plugged into the electrical outlet and the tanks are filled with water. The tanks or tubes inside the unit may be clogged. If the problem persists, it is possible that the taps are not working properly.
J
Jessica JonesAug 14, 2025
How to fix no hot water in my Honeywell HWTLMT508W Water Dispenser?
- A
  Alicia HodgeAug 15, 2025
  If your Honeywell Water Dispenser is not dispensing hot water, check if the hot switch is turned ON. If it is OFF, turn it ON and check the temperature after 30 to 45 minutes. The unit may have overheated; in that case, turn OFF both the hot and cold switches and let the unit rest for 1 hour. Also, if the hot switch is damaged, turn ON both switches again, ensuring there is water inside the tank.
D
Daniel ZimmermanAug 20, 2025
How to troubleshoot no cold water from Honeywell HWTLMT508W?
- S
  Sarah MiddletonAug 20, 2025
  If your Honeywell Water Dispenser is not dispensing cold water, check if the cold switch is turned ON. If it is OFF, turn it ON and check the temperature after 30 to 45 minutes. The unit may have overheated; in that case, turn OFF both the hot and cold switches and let the unit rest for 1 hour. Also, if the cold switch is damaged, turn ON both switches again, ensuring there is water inside the tank.
J
Jacob RodriguezAug 26, 2025
What to do if my Honeywell HWTLMT508W Water Dispenser is leaking?
- C
  Crystal GilbertAug 26, 2025
  If your Honeywell Water Dispenser is leaking, first empty the drip tray as it may be full. Also, check the water bottle cap and hose connections to make sure they are not loose. Turn off the cold and hot water switches and dry the unit on the outside and its surroundings.
N
Natalie GentryAug 30, 2025
Why does my Honeywell Water Dispenser have an odor?
- J
  jenniferperryAug 30, 2025
  If there is an odor in the water from your Honeywell Water Dispenser, and it is a new machine, please proceed with First Time Instructions on page 7. There may be an algae issue.
A
Aaron WattsSep 3, 2025
Why am I getting low electric shocks from my Honeywell HWTLMT508W?
- S
  Steven WilsonSep 3, 2025
  If you are experiencing low electric shocks from your Honeywell Water Dispenser, it may not be properly grounded. Please call a professional electrician to assist you with any electrical problem.

This document describes the Honeywell HWTLMT508W Table Top Water Dispenser, designed to provide hot, normal, and cold water. It is a user-friendly appliance with several safety and convenience features.

Function Description:

The Honeywell HWTLMT508W is a table-top water dispenser that offers three water temperature options: hot, normal, and cold. Users can dispense the desired water temperature by pressing down the corresponding tap. For hot water, a safety switch must be pressed simultaneously with the tap to prevent accidental dispensing of hot water. The unit features indicator lights for hot water, cold water, and power, which illuminate when the respective functions are active and turn off once the desired temperature is reached. The dispenser is designed for use with 10 or 20-liter water bottles, which are placed on top of the unit. A pointed funnel helps prevent spillage during bottle replacement. The unit also includes a drain plug for easy draining of water from the tanks, which is crucial for maintenance and storage.

Important Technical Specifications:

Model Number: HWTLMT508W
Voltage: 230V~
Frequency: 50Hz
Heating Power: 420W
Cooling Power: 65W
Total Power: 485W
Heating Capacity: 5L/h -> 90°C (meaning it can heat 5 liters per hour to 90°C)
Cooling Capacity: 1L/h -≤ 15°C (meaning it can cool 1 liter per hour to 15°C or below)
Water Bottle Compatibility: Designed for 10 or 20-liter bottles.

Usage Features:

Easy Installation: Before first use, the unit should stand upright for approximately 24 hours to allow the cooling system to settle. It requires a level, cool, and ventilated indoor location, away from direct sunlight and heat sources. A 6-inch clearance from the wall is recommended.
First-Time Setup: The dispenser is pre-cleaned, but the reservoir, hot, and cold water tanks, and water lines must be flushed with tap water before initial use. This involves filling the tanks, allowing water to sit, dispensing from all faucets, plugging in the unit, and then activating the hot and cold switches. The unit takes about 30-45 minutes to reach minimum hot and cold temperatures, at which point the indicator lights turn off.
Water Dispensing: Separate taps are provided for hot, normal, and cold water. The hot water tap includes a safety switch for added protection.
Bottle Replacement: To replace a water bottle, the unit should be turned off if the tanks are empty. The seal from the bottle lid is removed, and the 10 or 20-liter carboy is carefully lifted and inverted onto the dispenser's pointed funnel. The funnel tip breaks the bottle seal, allowing water to flow into the tanks.
Power Control: The unit has separate green (cold) and red (hot) switches on the back to control the cooling and heating functions. It is crucial to ensure water is in the tanks before turning on the heating function to prevent damage from overheating.
Indicator Lights: Three indicator lights (hot, cold, power) provide visual feedback on the unit's operational status.

Maintenance Features:

Cleaning: Before cleaning, both hot and cold switches must be turned OFF, and the unit unplugged. The exterior can be cleaned with a soft cloth and warm water, avoiding abrasive cleaners. The drip tray should be cleaned regularly by lifting it up and outward to prevent water buildup. The back of the machine, including the coils, can be cleaned with a duster or vacuum cleaner attachment.
Storage: For extended periods of non-use, the unit should be turned off, unplugged, and all water drained from the tanks via the faucets and drain plug. The unit must be stored upright and protected from dust.
Troubleshooting Guide: The manual includes a comprehensive troubleshooting guide to address common issues such as no water coming out, no hot/cold water, water leakage, odor in water, or low electric shocks. It advises contacting customer service for issues not covered or if problems persist.
Safety Precautions: The manual emphasizes important safety instructions, including using the correct electrical current (230V~, 50Hz), plugging into a properly installed Miniature Circuit Breaker (MCB), avoiding extension cords, and never operating with a damaged cord or plug. It also warns against running the power cord under carpets, attempting repairs, or allowing children to play with the appliance. The unit should never be used in bathrooms or outdoors.

Warranty:

The product comes with a 1-year warranty from Agile Brands Private Limited, valid only in India. The warranty covers defects in materials and workmanship, provided the product is properly installed, maintained, and operated according to instructions. It does not cover failures due to normal wear and tear, accident, abuse, misuse, alteration, misapplication, improper installation, or improper maintenance. The warranty is void if the water dispenser is modified, improperly installed or repaired, damaged by accident, fire, or misuse, or if the original serial numbers are removed, obliterated, or altered. Free after-sales service is available within the municipal limits of the company's office or dealer's location during the warranty period.