–19–
Data Field Descriptions
Field 46:
Enter up to 24 digits. Do not fill unused spaces. Enter 0-9, #+11 for ‘*’; #+12 for’#’; #+13 for a pause (2 seconds).
✼
46
“Follow Me Reminder” Phone Number
(QWHU XS WR GLJLWV
This option allows the user to schedule a time driven message. When
activated the system will dial the phone number programmed and deliver a
voice message (custom words 72, 73 and 74). This option is only supported
when the pager or follow me feature is enabled in field ✻49 (option 6-9 or
10-13).
If using the Follow Me Reminder feature, enter the phone number here. If
fewer than 24 digits are entered, exit by pressing [✻]. To clear entries from
the field press ✻46✻.
The telephone message can be terminated (acknowledged) by pressing any
key on the telephone keypad. Pressing any key on the local LYNXR keypad
will terminate (acknowledge) both the follow me and the local reminder
announcements.
Note:
The follow me reminder announcement will be terminated if any
other event requires the system to dial out or if and audible alarm
has occurred.
✼
47
Phone System Select
1RWH
)RU /<1;5/<1;5 RQO\ RSWLRQV DQG
DUH DSSOLFDEOH )RU /<1;5(1 DOO RSWLRQV DSSO\
&HQWUDO 'LDOLQJ 0RGH
6WDWLRQ 3XOVH 7RQH 3XOVH 7RQH
1R :$76
1R
6SHDNHU
3KRQH
1R
6SHDNHU
3KRQH
:LWK
6SHDNHU
3KRQH
:LWK
6SHDNHU
3KRQH
:$76
1R
6SHDNHU
3KRQH
1R
6SHDNHU
3KRQH
:LWK
6SHDNHU
3KRQH
:LWK
6SHDNHU
3KRQH
This option is used to enter the correct type of phone dialing (pulse or tone),
and to select the correct WATS line option for the Central Station. For
LYNXR-EN this option is used to activate the speaker phone option.
Note:
If using pulse dialing, you must enter the numbers slowly in order to
allow the pulse dialer time to operate.
✼
48
Report Format for Primary/Secondary
3ULPDU\ 6HFRQGDU\
6HH FKRLFHV EHORZ 6HH FKRLFHV EHORZ
$'(0&2 /RZ 6SHHG 6WDQGDUG
5DGLRQLFV 6WDQGDUG
$'(0&2 /RZ 6SHHG 6WDQGDUG
5DGLRQLFV 6WDQGDUG
$'(0&2 &RQWDFW ,' 5HSRUWLQJ ZLWK GLJLW
VXEVFULEHU DFFRXQW QXPEHU
$'(0&2 ([SUHVV
$'(0&2 &RQWDFW ,' 5HSRUWLQJ ZLWK GLJLW
VXEVFULEHU DFFRXQW QXPEHU
$'(0&2 /RZ 6SHHG ([SDQGHG
5DGLRQLFV ([SDQGHG
Enter ✻ as the 4th digit of ✻43 through ✻44, if 3+1 dialer reporting is to be
used. (For an explanation of these formats, see the System Communication
section of this manual.)
Notes:
(1) The maximum number of alarm and alarm restore reports
during one armed period is determined by field ✻92.
(2) If Option 5 is selected a 10-digit account number must be
entered in Fields ✻43 or ✻44.
(3) Option 5 or 7 (ADEMCO Contact ID® Reporting) must be
selected for AVM.
(4) Option 5 or 7 (ADEMCO Contact ID® Reporting) must be
selected if installing the 5842 Wireless Dialer.
✼
49
Split/Dual Reporting
7R 3ULPDU\ 7R 6HFRQGDU\
$OO UHSRUWV 1RQH XQOHVV SULPDU\
IDLOV WKHQ DOO
$ODUPV 5HVWRUH &DQFHO 2WKHUV
$OO H[FHSW 2SHQ&ORVH 7HVW 2SHQ&ORVH 7HVW
$ODUPV 5HVWRUH &DQFHO $OO
$OO H[FHSW 2SHQ&ORVH 7HVW $OO
$OO UHSRUWV $OO
7R 3ULPDU\ 7R 3DJLQJ 1XPEHU
$OO UHSRUWV H[FHSW 2SHQ&ORVH $ODUPV 2SHQ&ORVH
Â
7URXEOHV
$OO UHSRUWV $ODUPV 7URXEOHV
$OO UHSRUWV $ODUPV 2SHQ&ORVH
Â
7URXEOHV
$OO UHSRUWV H[FHSW 2SHQ&ORVH 2SHQ&ORVH
Â
7R 3ULPDU\ 7R )ROORZ 0H 6\VWHP
3KRQH 1XPEHU
$OO UHSRUWV H[FHSW 2SHQ&ORVH $ODUPV 2SHQ&ORVH
Â
7URXEOHV
$OO UHSRUWV $ODUPV 7URXEOHV
$OO UHSRUWV $ODUPV 2SHQ&ORVH
Â
7URXEOHV
$OO UHSRUWV H[FHSW 2SHQ&ORVH 2SHQ&ORVH
Â
Â
:LOO UHSRUW 8VHUV DQG LI XVLQJ ZLUHOHVV EXWWRQW\SH
GHYLFHV ZLOO UHSRUW WKH ]RQH QXPEHU RI WKH DUP RU GLVDUP
EXWWRQ $OO RWKHU ]RQHV DQG XVHUV DUH QRW UHSRUWHG
This field is used to select a reporting option as follows:
Enter: 0 - 5 when reporting to telephone receivers.
6 - 9 when reporting to a pager is desired.
10 - 13 when reporting to an auxiliary telephone receiver.
Pager Report Format
Options 6-9 send reports to the primary phone number, in a format defined
in Field ✻48, and send reports to a pager, which has its phone number
entered as the secondary phone number in Field ✻42. The pager report is a
7-digit code, with optional 16-digit prefix, in the following format:
AAAAAAAAAAAAAAAA-EEE–00NN
where:
AAA = Optional 16 digits for PIN number, etc. See Field ✻88 for full
description of these characters.
EEE = 3-digit Event Code as follows:
911 = Alarm (NN = zone number)
101 = Open, system disarmed (NN = user no.)
102 = Close, system armed (NN = user no.)
811 = Trouble (NN = zone no.)
00 = Always displayed before 2-digit user/zone no.
NN = 2-digit user number or zone number, depending on the type of
event (EEE) that occurred. NN=00 indicates AC loss, system low
battery, or low battery in 5827.
Follow Me System Report Format
Options 10-13 send reports to the primary phone number, in a format
defined in Field ✻48, and sends voice message to the secondary phone
number entered in Field ✻42.
The message is a repeatable system status announcement. If the manual
paging option has been programmed in Field ✻87, the message will repeat
“system, system…..”.
The message can be terminated by pressing any key on the telephone
keypad.
To Next Page
Loading...
Need help?
General
