–28–
✻
56 Enhanced Zone Programming Mode
While in Program mode, press
✻
56 to enter Zone Programming Menu Mode.
Refer to the zone assignment table for
✻
56 on the separate programming form.
The following explains the
✻
56 prompts in detail. The left two columns identify the prompts and list the
available entries for each. The right-most column provides a further explanation of the entries.
1RWH
<RX PD\ ILQG LW FRQYHQLHQW WR DGMXVW WKH YROXPH VHWWLQJ EHIRUH HQWHULQJ WKH 3URJUDPPLQJ 0RGH 7KLV ZLOO DOORZ \RX WR FOHDUO\ KHDU
IHHGEDFN DQQRXQFHPHQWV RU V\VWHP EHHSV
% -
Zone number
=RQH QXPEHU
>
✻
@ FRQWLQXH
H[LW =RQH 3URJUDPPLQJ PRGH
Enter the 2-digit zone number to be programmed and the Voice Descriptor
for the selected zone number will be announced, if it is programmed. Press
[
✻
] to advance.
•
Zone 01 = hardwire
•
Zones 02-25 = RF zones (only)
•
Zones 26-41 = Button zones (only)
•
Zone 92 = Duress
•
Zones 95, 96, 99 = Panic zones
Pressing 00 exits mode, upon which the prompt “56” blinks, indicating the
mode is inactive. Press [
✻
] + any field number to go to that field.
E
]W
Zone type
]RQH W\SH
>
✻
@ FRQWLQXH
>@ UHWXUQ WR SUHYLRXV SURPSW
1RWH
,I LV DFFHSWHG DV D ]RQH W\SH VDYH WKH
]RQH W\SH DQG DGYDQFH WR WKH FRQILUP GHOHWH
SURPSW )
Each zone must be assigned to a zone type, which defines the way in
which the system responds to faults in that zone. Enter the 2-digit zone
type for this zone as follows:
00 = Not Used 08 = 24 Hr Aux
01 = Entry/Exit #1 09 = Fire without verify
02 = Entry/Exit #2 10 = Interior w/Delay
03 = Perimeter 20 = Arm–Stay
04 = Interior Follower 21 = Arm–Away
05 = Trouble Day/Alarm Night 22 = Disarm
06 = 24 Hr Silent 23 = No Alarm Response
07 = 24 Hr Audible 24 = Silent Burglary
'
UF
Report code
(QWHU WKH UHSRUW FRGH IRU WKLV ]RQH
>
✻
@ FRQWLQXH
>@ UHWXUQ WR SUHYLRXV SURPSW
The report code consists of 2 hexadecimal digits, each in turn consisting of
2 numerical digits. For example, for a report code of "3C", enter [0][3] for
"3" and [1][2] for "C".
If this is Zone 1, 95, 96 or 99, the system skips to the VOICE
DESCRIPTOR prompt (1C).
G
L
Input type
5) VXSHUYLVHG 5) ²
VHQGV SHULRGLF FKHFNLQ VLJQDOV IDXOWV
UHVWRUH DQG ORZ EDWWHU\ VLJQDOV
1RWH 5) W\SH WUDQVPLWWHUV PXVW UHPDLQ ZLWKLQ
UDQJH RI WKH UHFHLYHU RWKHUZLVH D
VXSHUYLVLRQ IDLOXUH VLJQDO ZLOO RFFXU
85 XQVXSHUYLVHG 5) ² VHQGV VDPH DV
´5)µ W\SH EXW FRQWURO GRHV QRW VXSHUYLVH
WKH FKHFNLQ VLJQDOV
%5 EXWWRQ W\SH ² VHQGV RQO\ IDXOW DQG ORZ
EDWWHU\ VLJQDOV GRHV QRW VHQG UHVWRUHV RU
FKHFNLQ VLJQDOV
1RWH 85 DQG %5 W\SH WUDQVPLWWHUV PD\ EH FDUULHG
RII SUHPLVHV RXW RI UDQJH ZLWKRXW FDXVLQJ D
VXSHUYLVLRQ IDLOXUH
>
✻
@ FRQWLQXH
>@ UHWXUQ WR SUHYLRXV SURPSW
Enter the input type for the transmitter assigned to this zone. Refer to the
transmitter’s instructions for input types of each transmitter.
Note:
Zones 2-25 should be assigned Input Type 3 or 4 . Zones 26-41
should be assigned Input Type 5 only.
)
O
Loop number or Loop and Serial
number
(if using RF Learning)
ORRS QXPEHU IRU WKH ]RQH RI WKH
WUDQVPLWWHU EHLQJ HQWHUHG
>
✻
@ FRQWLQXH WR '(/(7( =21(
3$5$0(7(56 &21),50$7,21
SURPSW )
>
✻
@ FRQWLQXH WR WKH (152// 02'( SURPSW
$ LI QRW HQWHUHG RU 92,&(
'(6&5,3725 SURPSW LI DOUHDG\ HQWHUHG
>@ UHWXUQ WR SUHYLRXV SURPSW
This prompt can be used to enroll loop number and serial number
via RF transmission or the loop number can be enrolled manually.
If using the RF Learning Mode, there is no need to manually enter
a loop number. Proceed directly to RF Learning
Notes: (1)
BR type devices cannot be enrolled by using UR or RF type.
Likewise, UR or RF type devices cannot be enrolled by using a
BR type device. There is a 52-second time-out for RF
enrolling. At the end of the time-out, the system returns to
the INPUT TYPE prompt (d). If enrolled, loop number and “L”
are displayed.
(2) Once encrypted (high-security) devices have been
enrolled they must be activated. Refer to the device’s
Installation Instructions to activate the High-Security
Mode.
To Next Page
Loading...
Need help?
General
