–29–
✻
56 Enhanced Zone Programming Mode
RF Learning
- Two (2) transmissions (2 key depressions) at least 5
seconds apart will be required for BR type devices (device type 5). Two
beeps will sound after the second transmission, confirming that the loop
number and serial number have been learned.
For all other device types, four (4) transmissions are required (fault,
restore and fault, restore). A single beep will sound after the second
transmission confirming that the loop and serial number have been
captured. Following the fourth transmission the system will confirm that
the loop number and serial number have been learned and announce the
Voice Descriptor for the zone, if it is programmed, followed by two beeps.
Press [
✻
] to continue.
Manual Entry
- Enter the desired loop number and press [
✻
] to
continue (see the transmitter’s Installation Instructions for specific loop
designations).
Note:
The loop number can be changed even if the zone has already
been entered. Care should be taken when using this feature as it
has the capability to make zones inoperable by creating a
mismatch of a working serial number/loop number combination.
This should be re-confirmed if the loop number is changed.
“L” indicates that the zone’s serial number has already been enrolled.
*
Delete zone parameters
confirmation
GLVFDUG WKH GHOHWH UHTXHVW
FRQILUP UHTXHVWHG GHOHWH
1RWH ,I ZDV HQWHUHG DV D ]RQH W\SH LQ SURPSW
E ZLOO EH UHWDLQHG DQG V\VWHP ZLOO
DGYDQFH WR SURPSW &
This function deletes either the serial number or all zone information
that is programmed for the zone.
If “00” was entered in the zone type, the confirmation of the delete
request will delete all information associated with the zone currently
being programmed.
If “0” was entered in the loop number, the confirmation of the delete
request will delete the serial number of to the zone currently being
programmed.
-%
0'
Enroll mode
DGYDQFH WR WKH 92,&( '(6&5,3725
SURPSW &
1RWH 7KLV ZLOO VDYH DOO ]RQH SDUDPHWHUV
HQWHU QRZ DQG SURFHHG WR 6(5,$/
180%(5 SURPSW E
1RWH 1RW DSSOLFDEOH LI WKH VHULDO QXPEHU LV
DOUHDG\ SUHVHQW
FRS\ WKH ODVW VHULDO QXPEHU HQWHUHG LQWR
ORFDO UDP
1RWH ,I WKLV LV WKH VW ]RQH QRQH ZLOO EH LQ WKH
EXIIHU DQG WKH SDQHO ZLOO HPLW D ORQJ WRQH
1RW YDOLG LI VHULDO QXPEHU LV DOUHDG\ SUHVHQW
YLHZ H[LVWLQJ VHULDO QXPEHU
1RWH 2QO\ LI ´
/
µ LV GLVSOD\HG ,I ´
/
µLVQRW
GLVSOD\HG SDQHO ZLOO HPLW D ORQJ EHHS
DGYDQFH WR ) GHOHWH H[LVWLQJ VHULDO
QXPEHU
1RWH 2QO\ LI ´
/
µ LV GLVSOD\HG ,I ´
/
µLVQRW
GLVSOD\HG SDQHO ZLOO HPLW D ORQJ EHHS
>
✻
@ DGYDQFH WR WKH 92,&( '(6&5,3725
SURPSW & 7KLV ZLOO VDYH DOO ]RQH
SDUDPHWHUV
>@ UHWXUQ WR WKH /223 180%(5 SURPSW
(
1RWH ,Q RUGHU IRU DOO HQWHUHG SDUDPHWHUV WR EH
DFFHSWHG \RX PXVW DGYDQFH WR WKH 92,&(
'(6&5,3725 SURPSW &
If “L” is displayed, the serial number for this transmitter has already
been entered. It may, however, still be viewed, confirmed (only if in
listen mode), or deleted.
View serial number
Enter “3”. Each digit will be redisplayed, and the keypad will beep once
for digits 1-6, and three times for the last digit.
Confirm serial number
The serial number/loop number combination can be confirmed after one
transmission from a BR type device or two transmissions (fault and
restore) from a UR or RF type device. If a transmission is received that
matches the serial number and loop number entered, the system will
confirm the reception by announcing the Voice Descriptor for the zone, if
it is programmed, followed by three beeps, and a “C” will appear on the
display indicating the received serial number and loop number have
been confirmed. No further transmissions will be received.
Delete serial number
The serial number can be deleted by entering “9”.
If “L” is not displayed, the serial number for this transmitter has not
been previously entered. You may enter the serial number manually,
copy the previous serial number, return to Prompt (E) or enter the serial
number later using the ✻83 Enhanced Sequential Mode.
To Next Page
Loading...
Need help?
General
