Honeywell TCC800M User Manual

2. The default protocol
is Alpha, but
depending on the
control panel version,
you may need to
change this to V2.
3. To change to V2: While inserting the
new battery, press the Disarm and Part
Arm buttons.
4. To change to Alpha: While inserting
the battery, press the Total Arm and
Disarm buttons.
The LED related to buttons B1 and
B2 pushed will light for 3 seconds then
after they will light off and if
Alpha: LED of B1 and B2 flash for 8s
V2: LED of B1 and B2 flash for 3s.
The new protocol is retained in memory,
and is not affected by the user changing
the battery.
B3
B1 B2
LED
B4 B3
B1 B2
LED
B4 B3
B1 B2
LED
B4
Keyfob TCC800M, TCC8M
This keyfob can be used with all Domonial
panels from version I onwards, radio
modules CO79, CO79-2 and 5882EUHS
supporting the Alpha protocol and on older
panels that support the V2 protocol (HF
keyfob models). In the latter case, the TCC
keyfob simulates a TC805HF keyfob.
Battery Specification
It is recommended that only the following 3V
battery is used: CR2032 by Panasonic or GP.
- Button 1: Arm
Total Set
- Button 2: Disarm
- Button 3: Arm
Partial Set
- Button 4: System
Status
- SOS: Buttons
1 and 3 send an
immediate alert
when depressed
simultaneously for
2 seconds.
TCC Base and Belt Hook
To fix the TCC to a wall, unclip it from its
base and screw the base to the wall, using
the two screw holes (screws not supplied).
To fix it to a belt, slide the belt hook upwards
into the slot provided in the base of the TCC.
Registration and Configuration
1. First, set the panel to registration mode.
Changing the Battery / Protocol
1. To change the battery, remove
the TCC keyfob from its base and
unscrew the battery compartment with
a screwdriver.
2. To register the TCC keyfob, press
buttons 1 and 3. To register the keyfob with
a different panel, remove and replace the
battery before registering as usual.
Configuration is performed with
a programming tool. Total, Annex or
Total + Annex.

Honeywell TCC800M Specifications

General

Brand	Honeywell
Model	TCC800M
Category	Remote Control
Language	English

Summary

Honeywell Keyfob TCC800M/TCC8M Overview

Keyfob Compatibility and Function

Details compatibility with Domonial panels and simulation of TC805HF keyfob.

Keyfob Battery and Button Functions

Recommended Battery Specification

Specifies the recommended 3V battery: CR2032 by Panasonic or GP.

Keyfob Button Operations

Details functions of Arm, Disarm, Partial Set, System Status, and SOS alert buttons.

Keyfob Installation and Setup

TCC Base and Belt Hook Mounting

Instructions for fixing the TCC keyfob to a wall or a belt.

Keyfob Registration and Configuration

Steps for setting the panel to registration mode and pairing the keyfob.

Keyfob Maintenance and Protocol Settings

Battery Replacement Procedure

Instructions for removing the keyfob and unscrewing the battery compartment.

Protocol Selection (Alpha/V2)

How to change the keyfob protocol to Alpha or V2 during battery replacement.

LED Indicators for Protocol Status

Explanation of LED flashes indicating Alpha or V2 protocol status.

Keyfob Technical Specifications

Identification Rings

Information on using colored rings to identify keyfobs.

Safety Recommendations

Warnings regarding battery replacement risks and proper disposal.

Product Characteristics

Details dimensions, weight, battery type, battery life, temperature, humidity, radio, and consumption.

Certifications and Compliance

Lists certifications (NF&A2P, EN 50131) and links to compliance information.