Need help?Do you have a question about the Honeywell TrueIAQ DG115EZIAQ and is the answer not in the manual?
General| Type | Remote Control |
|---|---|
| Brand | Honeywell |
| Model | DG115EZIAQ |
| Category | Remote Control |
| Display | LCD |
| Power Source | Battery |
| Functions | Temperature control, humidity control, fan control, system mode selection |
Provides feedback on indoor air quality conditions.
Shows current outdoor temperature and humidity.
Indicates which equipment is currently active.
Navigates through IAQ equipment control options.
Displays current indoor temperature and humidity.
Manages time-based IAQ equipment programming.
Alerts for required equipment maintenance.
Confirms and saves changes made to settings.
Adjusts IAQ equipment comfort settings.
Indicates indoor humidity levels below 20% RH.
Indicates indoor humidity levels above 60% RH.
Protects against excess humidity based on outdoor conditions.
Signals humidity addition or removal requests.
Shows when fresh air ventilation is active.
Timer-based alerts for required component service.
Adjusts humidifier target humidity using arrow buttons.
Provides humidity settings based on outdoor temperature.
Explains setpoint logic for combined humidifier/dehumidifier use.
Configures the level of frost protection.
Selects the humidifier operation mode (Auto/Off).
Saves the configured humidifier settings.
Adjusts the target humidity for dehumidification.
Selects the dehumidifier operation mode (Auto/Off).
Saves the configured dehumidifier settings.
Temporarily activates ventilation for a set duration.
Selects the ventilation operation mode (Auto/ON/OFF).
Saves the configured ventilation settings.
Modifies the hour setting for the device's clock.
Modifies the minute setting for the device's clock.
Confirms and saves the adjusted time settings.
Displays service alerts for various system components.
Resets service timers by holding the DOWN arrow.
Cautionary notice regarding electrical shock or equipment damage.
Ensures system power is off before commencing installation.
Guidance on choosing an appropriate mounting location.
Instruction to loosen the device's cover screw.
Procedure to detach the front housing from the base.
Wiring procedure for wall-mounted installations.
Step for attaching the side wall clip during duct mounting.
Instruction to reattach and secure the front housing.
Critical note for aligning the sensor cap in duct mounting.
Final step to apply power to the installed system.
Description of the R terminal for 24V power supply.
Description of the C terminal for 24V power common.
Description of the Sensor terminal for communication.
Description of the Switch terminal for override input.
Description of the W terminal sensing heat calls.
Description of the G terminal for fan calls and output.
Description of the Vent 1 terminal for damper control.
Description of the Dehum 1 terminal for dehumidifier control.
Description of the Hum 1 terminal for humidifier control.
Diagram showing wiring for a non-powered humidifier setup.
Diagram illustrating wiring for a powered humidifier setup.
Wiring diagram for integrating with TrueSTEAM.
Wiring diagram for dehumidifier and ventilation damper.
Wiring diagram for humidifier and HRV/ERV ventilator.
Diagram for humidifier, damper, and exhaust fan wiring.
Recommendation to avoid south-facing or direct sunlight.
Maintain minimum clearance from exhaust vents.
Guideline for sensor placement near air intakes.
Mount sensor above potential snow accumulation levels.
Warning to avoid routing sensor wire near high voltage wires.
Information on extending the sensor wire using 18-gauge wire.
Procedure to enter setup mode by holding arrow buttons.
Using the 'More' button to navigate setup steps.
Using UP/DOWN arrows to choose configuration options.
Using 'Done' to save settings and return to the home screen.
Configures temperature units: Fahrenheit or Celsius.
Recalibrates indoor temperature sensor readings.
Recalibrates outdoor temperature sensor readings.
Sets the level of protection against window frost.
Sets the upper limit for indoor humidity control.
Configures humidifier operation modes.
Enables or disables humidity programming.
Sets the start time for programmed humidity.
Sets the end time for programmed humidity.
Configures the type of dehumidifier terminal equipment.
Sets the high limit for dehumidification.
Sets the low limit for dehumidification.
Configures dehumidifier operation modes.
Recalibrates humidity sensing accuracy.
Sets humidifier service timer intervals (continuous).
Sets intermittent humidifier service timer intervals.
Sets humidifier water filter service intervals.
Sets air filter service timer intervals.
Sets ventilation filter service timer intervals.
Configures the type of ventilation filter service required.
Sets UV bulb replacement reminder intervals.
Configures various ventilation control options.
Configures ventilation operation modes.
Enables or disables programmed ventilation schedules.
Sets the start time for programmed ventilation.
Sets the end time for programmed ventilation.
Configures ASHRAE settings based on number of bedrooms.
Configures ASHRAE settings based on home square footage.
Sets the ASHRAE CFM value for ventilation.
Configures the maximum ventilation rate.
Configures conditions for automatic ventilation shut-off.
Controls dehumidification using fresh air ventilation.
Details operating temperature, humidity range, and accuracy.
Covers power supply, spike, and over-voltage protection.
Describes clock backup, output state, and parameter storage.
Includes dimensions, weight, and display unit information.
Details warranty period and covered defects.
Outlines steps for returning products or contacting support.
Covers excluded costs, liability, and exclusive warranty terms.
Explains consumer rights and provides contact for questions.
To Next Page