What does 'Telco Fault' mean on my Honeywell Security System?
The 'Telco Fault' message on your Honeywell Security System, along with 'Check 94', indicates that the Telephone Line Fault Monitor is enabled in *92, but the panel isn't detecting at least 3Vdc on the phone line.
Why is my Honeywell VISTA-15P panel not sending signals immediately or not at all?
If your Honeywell Security System panel is not sending signals immediately or not at all, check the *50 Dialer Delay setting.
Why is my Honeywell VISTA-15P keypad not providing exit beeps when arming Away or Max?
If your Honeywell Security System keypad isn't providing exit beeps when arming in Away or Max mode, ensure that *37 'Audible Exit Warning' is enabled for exit beeps on all keypads. Also, keypad sounds may be suppressed in the second digit of the keypad addressing fields *190 - *196. This can suppress Chime, Entry/Exit, and Arm/Disarm beeps from specific keypads.
What could cause the on-board panel zone(s) of my Honeywell VISTA-15P Security System to stay faulted?
If the on-board panel zone(s) of your Honeywell Security System are staying faulted, check the values of the resistors used. Also, verify each zone program option of 'Hardwire Type' to ensure it matches the zone wiring. Finally, make sure the zone circuits connected to the panel are NOT offset by one or more terminals.
What does 'Bell Failure' mean on my Honeywell VISTA-15P Security System?
The message 'Bell Failure' along with 'Check 70' on your Honeywell Security System indicates that bell supervision has been enabled, and an EOLR (End-of-Line Resistor) should be connected.
Why am I getting a long beep when adding user codes to my Honeywell VISTA-15P Security System?
If you receive a long beep when adding user codes to your Honeywell Security System, it means the panel is preventing you from duplicating user codes.
What does 'AC Loss' mean on my Honeywell VISTA-15P?
If your Honeywell Security System displays 'AC Loss', it indicates that the system's AC power voltage has dropped below the threshold of 16.5VAC.
How to troubleshoot a 'Comm Fail' error on my Honeywell VISTA-15P Security System?
If your Honeywell Security System displays a 'Comm Fail' error, and you are not using a phone line, disable the dialer by removing the phone numbers from the panel. You can do this by entering *40*, *41*, and *42.
What does 'Lo Bat' mean on my Honeywell VISTA-15P?
If your Honeywell Security System displays 'Lo Bat' without a zone number, it indicates that the system battery is either low or disconnected.
How to fix a Honeywell Security System keypad that is locking up after 3-4 button presses?
If your Honeywell Security System keypad locks up after a few button presses, ensure that the keypad's address is unique and doesn't match any other keypad on the system, as address conflicts can cause lockups. Also, a shorted green wire can prevent commands from reaching the panel. If multiple devices are on the ECP, connect them one at a time to isolate the problematic wire run.
General| Control Panel Type | Hardwired |
|---|---|
| Zones | 8 |
| Partitions | 1 |
| User Codes | 48 |
| Keypads | Up to 8 |
| Event History | 100 events |
| Event Log | 100 events |
| Communication | Phone line, Cellular |
| Wireless Compatibility | Honeywell 5800 series wireless devices |
| Battery Backup | 7Ah |
| Outputs | 2 |
Provides a general overview of the Honeywell security system's capabilities.
Covers core functionalities like burglary, fire protection, and security codes.
Details how to arm, step-arm, and disarm the system.
Explains remote system control via telephone.
Describes Alpha and Fixed-Word keypads and their features.
Details the purpose and operation of specific keypad keys.
Explains LED indicators and message displays on keypads.
Manages time for arming/disarming and alarm avoidance.
Verifies all zones are closed or bypassed.
Explains STAY, AWAY, INSTANT, and MAXIMUM arming options.
Procedures for disarming and clearing alarm states.
How to exclude specific zones from arming.
Using chime alerts for door/window openings.
Activating emergency responses via designated keys.
Creating and using macros for automated sequences.
Configuring automatic and manual pager notifications.
Managing user access and permissions.
Managing and arming multiple system partitions.
Automating system actions based on time.
Recording, viewing, and understanding system events.
Performing weekly checks for proper operation.
Identifying and resolving system issues and faults.
Routine care, cleaning, and battery replacement.
Details residential fire detection and alarm functionality.
Procedures to manage fire alarm events.
Guidelines for fire escape routes and safety.
A summary of basic system operations.
Overview of system sounds and display messages.
Compliance information and safety precautions.
Potential failure points and operational constraints.
Details the product's warranty coverage.
To Next Page