Honeywell VISTA-21iP - Page 18

*56 ZONE PROGRAMMING WORKSHEET [default shown in brackets]
Zone Zn Type Part. Report Hardwire
Type
Rsp. Time Location
1
[09] [1] [EOL] [1]
2
[01] [1] [EOL] [1]
3
[03] [1] [EOL] [1]
4
[03] [1] [EOL] [1]
5
[03] [1] [EOL] [1]
6
[03] [1] [EOL] [1]
7
[03] [1] [EOL] [1]
8
[03] [1] [EOL] [1]
Zone Zn Type Part. Report Input Type Loop Serial No. Location
9
[1] [RF]
10
[1] [RF]
11
[1] [RF]
12
[1] [RF]
13
[1] [RF]
14
[1] [RF]
15
[1] [RF]
16
[1] [RF]
17
[1] [RF]
18
[1] [RF]
19
[1] [RF]
20
[1] [RF]
21
[1] [RF]
22
[1] [RF]
23
[1] [RF]
24
[1] [RF]
25
[1] [RF]
26
[1] [RF]
27
[1] [RF]
28
[1] [RF]
29
[1] [RF]
30
[1] [RF]
31
[1] [RF]
32
[1] [RF]
33
[1] [RF]
34
[1] [RF]
35
[1] [RF]
36
[1] [RF]
37
[1] [RF]
38
[1] [RF]
39
[1] [RF]
40
[1] [RF]
41
[1] [RF]
42
[1] [RF]
43
[1] [RF]
44
[1] [RF]
45
[1] [RF]
46
[1] [RF]
47
[1] [RF]
48
[1] [RF]
49
[1] [BR]
50
[1] [BR]
51
[1] [BR]
52
[1] [BR]
53
[1] [BR]
54
[1] [BR]
55
[1] [BR]
56
[1] [BR]
57
[1] [BR]
58
[1] [BR]
59
[1] [BR]
60
[1] [BR]
61
[1] [BR]
62
[1] [BR]
63
[1] [BR]
64
[1] [BR]
95
[00] N/A
**
N/A N/A N/A
keypad [1] / [∗]
96
[00] N/A
**
N/A N/A N/A keypad [3] / [#]
99
[06] N/A
**
N/A N/A N/A
keypad [∗] / [#]
** Emergency key zones 95, 96, and 99 report the partition of the keypad used to activate the emergency zones.
NOTES:
Zone Type: see chart in
∗56 Zone Programming
Menu mode section.
Report Code: enabled if
first digit is a non-zero
number
Hardwire Type (zns 2-8):
0 = EOL 3 = ZD
1 = NC 4 = DB
2 = NO
Input Type:
2 = AW (zones 9-48)
3 = RF (zones 9-48)
4 = UR (zones 9-48)
5 = BR (zones 49-64)
NOTE: Zones 9-16 not
available if zone
doubling enabled.
Response Time:
0 = 10msec
1 = 350msec
2 = 700msec
3 = 1.2 sec
Reserved Zones
91 = addressable device
report enable/disable
default zone type =
[05].
92 = Duress report
enable/disable
– 18 –
WWW.DIYALARMFORUM.COM