Hoover HDIH 2T1047-80

Questions and Answers

K
kwilliamsAug 10, 2025
Why Hoover Dishwasher doesn't start?
- T
  Tracie VargasAug 10, 2025
  Your Hoover Dishwasher might not start due to several reasons: the door isn't closed properly, a delay start is set, the mains plug isn't connected, or a fuse in the house circuit is damaged. Make sure the appliance door is fully closed, check the delay start settings, connect the mains plug securely, and replace the fuse if necessary. Also, refill rinse aid and softener salt until full, pressing the button for 3 seconds after each refill.
A
Ashley AndersonAug 16, 2025
Why Hoover HDIH 2T1047-80 won't start?
- L
  Logan StevensonAug 16, 2025
  If your Hoover Dishwasher doesn't start, stops mid-cycle, or the indicator light is on, check these: * Ensure the appliance door is fully closed. If the delay start is set, refer to the displayed time. * Verify the mains plug is securely connected. * Inspect the house circuit fuse and replace it if damaged. * Check the rinse aid dispenser and refill it until full, then press the button for 3 seconds. * Ensure the softener salt tank is full with specific salt, then press the button for 3 seconds after refilling.
K
kramosAug 28, 2025
What to do if Hoover HDIH 2T1047-80 displays error codes?
- M
  michael66Aug 28, 2025
  If your Hoover Dishwasher shows an error code, here's what to check: * Ensure the water tap is open and the water inlet hose isn't kinked or bent. If you solve the error, switch off the appliance and restart the program. Also, make sure that the position of the hose is correct. * Check for clogs in the water inlet and ensure adequate water pressure. Clean the filter at the inlet hose connections at the tap and the rear of the appliance. Contact your local water authority to check water flow from tap. * If the anti-flood device is activated due to water leakages: close the water tap, disconnect the appliance from the power supply, and contact service.
E
Erika SmithSep 3, 2025
How to prevent water spots on Hoover HDIH 2T1047-80?
- P
  Patrick RodriguezSep 3, 2025
  If you notice dry water drop stains on glasses and dishes after using your Hoover Dishwasher, consider the following: * Increase the released quantity of rinse aid. * Replace the rinse aid or Multitab cleaning product if it's too old. * If the dishes are wet after a cycle, slightly open the dishwasher door (about 100°) to aid the drying process. * Refill the rinse aid dispenser and reset the rinse aid indicator. * Replace the rinse aid or Multitab cleaning product if it's too old.
M
Michael MckenzieNov 21, 2025
What to do if Hoover Dishwasher not cleaning properly?
- L
  Luis FigueroaNov 21, 2025
  If your Hoover Dishwasher isn't cleaning dishes properly, consider these potential causes and solutions: * Clogged filters: Clean the filters. * Incorrectly assembled filters: Make sure that the filters are correctly assembled and installed. * Clogged spray arms: Remove any food remnants with a thin, pointed object. * Inappropriate program: Ensure the selected program is suitable for the load and food remnants. * Incorrect item placement: Arrange items in the baskets so water can reach all surfaces. * Obstructed spray arms: Ensure items aren't blocking the spray arms. * Insufficient detergent: Use the correct amount of detergent. * Cycle interruption: Avoid opening the door or cutting power during the wash cycle. * Excessive rinse aid: Decrease the amount of rinse aid di...

Hoover HDIH 2T1047-80 Specifications

General

Appliance placement	Freestanding
Number of Place Settings	10
Energy Efficiency Class	E
Noise Level	47 dB
Control panel colour	Black
Inlet hose length	1.5 m
Outlet hose length	1.5 m
Drying system	Condensation
Delayed start timer	Yes
Water consumption per cycle	9 L
Energy consumption per 100 cycles	76 kWh
Drying Efficiency Class	A
Half Load Option	No
Delay Start	Yes
Washing programs	Eco, Intensive, Normal
Height	850 mm
Width	60 cm
Depth	600 mm
Delay start (max)	24 h
Wash Programs	Eco, Intensive, Normal