Hoover SH40080 User Manual (English)

Questions and Answers:

J
Jay PerezAug 14, 2025
Why won't my Hoover SH40080 run?
- J
  Juan DavenportAug 15, 2025
  There are several reasons why your Hoover Vacuum Cleaner might not be running: * It may not be correctly plugged into the electrical outlet. Ensure the plug is securely pushed into the outlet. * The electrical outlet itself may not be working. Check the fuse or breaker in your home and replace the fuse or reset the breaker, or consult an electrician. * The cleaner motor Thermal Protector may have tripped. If this is the case, switch off and unplug the vacuum cleaner and leave it for 30 minutes before switching it back on.
K
Karen BooneAug 18, 2025
Why is my Hoover SH40080 not picking up?
- M
  marcusrayAug 18, 2025
  Your Hoover Vacuum Cleaner might not be picking up due to a few common reasons: * The filters may be clogged. * The dirt cup might be full or blocked. * The dirt cup may be incorrectly installed.
A
Amanda PadillaAug 21, 2025
Why won't my Hoover SH40080 Vacuum Cleaner turn on?
- M
  Mrs. Sabrina EstradaAug 21, 2025
  Your Hoover Vacuum Cleaner might not be running due to a few reasons. First, ensure the plug is securely pushed into the electrical outlet. If it is, check the fuse or breaker in your home and replace the fuse or reset the breaker if necessary, or consult an electrician. Also, the cleaner motor Thermal Protector may have tripped; in that case, switch off and unplug the vacuum cleaner and leave it for 30 minutes before switching it back on.
C
Christina RodriguezAug 25, 2025
What to do if the Hoover SH40080 Vacuum Cleaner power nozzle brushroll won’t run?
- W
  wmcknightAug 26, 2025
  If the power nozzle brushroll on your Hoover Vacuum Cleaner isn’t running, consider these potential causes: * The hose power cord may not be firmly plugged in. Ensure it's securely plugged into the receptacle on the cleaner base. * The belt might be broken or worn, requiring replacement. * The brushroll switch may be set to “OFF”. Set the Brushroll switch to “ON”. * The power nozzle motor protector may have activated. * The brushroll might be jammed.
B
Brian SmithAug 28, 2025
Why is dust escaping from my Hoover SH40080?
- B
  Brandy JamesAug 28, 2025
  Dust might be escaping from your Hoover Vacuum Cleaner due to these reasons: * The filters may not be installed correctly. * The dirt cup may be incorrectly installed. Remove the Dirt Cup from the unit by pressing the Dirt Cup Release Button and reattach it to the unit, ensuring it is locked firmly back into place. * The filters may be clogged.
C
crobertsAug 31, 2025
What to do if dust is escaping from my Hoover SH40080 Vacuum Cleaner?
- K
  Kathleen FullerAug 31, 2025
  If dust is escaping from your Hoover Vacuum Cleaner, there might be a problem with the installation of the filters, so check them. Also, the dirt cup may be incorrectly installed. Remove the Dirt Cup from the unit by pressing the Dirt Cup Release Button and reattach it to the unit, ensuring it is locked firmly back into place. The filters may also be clogged.
L
laurenwallSep 4, 2025
Why won't the power nozzle brushroll run on my Hoover Vacuum Cleaner?
- M
  Mary MaloneSep 4, 2025
  The power nozzle brushroll on your Hoover Vacuum Cleaner might not run because the hose power cord is not firmly plugged in, so plug it firmly into the receptacle on the cleaner base. It could also be due to a broken or worn belt, which would need replacement. Also, ensure the brushroll switch is set to “ON”.
T
Timothy VegaSep 7, 2025
What to do if my Hoover Vacuum Cleaner nozzle won’t pick up?
- A
  Andrew JacksonSep 7, 2025
  If your Hoover Vacuum Cleaner nozzle isn’t picking up, check for a blockage in the nozzle connector and remove it. Also, the brushroll might not be running, or the brushroll brushes may be worn and in need of replacement.
Q
qwilliamsSep 12, 2025
What to do if Hoover SH40080 nozzle won’t pick up?
- D
  daniellejordanSep 12, 2025
  If your Hoover Vacuum Cleaner nozzle isn’t picking up, it could be due to: * A blockage in the nozzle connector. Remove the blockage. * The brushroll not running. * Worn brushroll brushes. Replace the brushes.