Horizon Hobby E-flite Night Timber X User Manual (English)

Questions and Answers:

M
max47Aug 13, 2025
How to fix oscillation in Horizon Hobby Toy?
- J
  Jasmine YoungAug 13, 2025
  Oscillation in your Horizon Hobby Toy can stem from several factors. Check for a damaged or imbalanced propeller or spinner and replace if necessary, balance the propeller. Motor vibration could also be the culprit; replace parts, align them correctly, and tighten fasteners. Ensure the receiver is securely aligned in the fuselage. Loose aircraft controls should be tightened, securing servos, arms, linkages, horns, and control surfaces. Replace any worn parts, particularly the propeller, spinner, or servo. Finally, irregular servo movement indicates the servo should be replaced.
C
Christine FarmerAug 17, 2025
Why is my Horizon Hobby E-flite Night Timber X Toy's flight time reduced?
- J
  jenkinsgloriaAug 17, 2025
  If your Horizon Hobby Toy experiences reduced flight time or feels underpowered, start by fully recharging the flight battery. Ensure the propeller is installed correctly with the numbers facing forward. A damaged flight battery should be replaced following the battery instructions. Cold flight conditions can also affect performance, so warm the battery before use. If the battery capacity is too low for the conditions, consider replacing it with a larger capacity battery.
T
tinafloresAug 20, 2025
What to do if Horizon Hobby Toy doesn't respond to throttle?
- B
  Betty HayesAug 21, 2025
  If your Horizon Hobby Toy responds to other controls but not to the throttle, first ensure the throttle stick and trim are at their lowest settings. Confirm that the throttle servo travel is at least 100%. Check if the throttle channel is reversed and correct it on the transmitter if needed. Also, verify that the motor is properly connected to the ESC.
J
Jasmin DavisAug 25, 2025
Why Horizon Hobby E-flite Night Timber X Toy will not connect to transmitter after binding?
- C
  chadmorrisonAug 26, 2025
  If your Horizon Hobby Toy doesn't connect to the transmitter after binding, try moving the powered transmitter a few feet away from the aircraft and then disconnect and reconnect the flight battery. Ensure that neither the aircraft nor the transmitter is near large metal objects, wireless sources, or other transmitters. Make sure the bind plug is removed before cycling power after rebinding the transmitter. If using ModelMatchTM radios, select the correct model memory on the transmitter. Replace or recharge batteries if the flight or transmitter battery charge is low. If the transmitter was bound to a different aircraft using a different DSM protocol, rebind the aircraft to the transmitter.
J
Jessica BishopAug 29, 2025
Why control surface on Horizon Hobby Toy doesn't move?
- C
  Casey CaldwellAug 29, 2025
  If a control surface on your Horizon Hobby Toy doesn't move, check for damage to the control surface, control horn, linkage, or servo, and repair or replace parts as needed. Inspect wires and connections, connecting or replacing them if necessary. Ensure the transmitter is correctly bound or that the correct aircraft is selected in the transmitter. Fully recharge the flight battery. If the BEC of the ESC is damaged, replace the ESC.
J
Jonathan EdwardsSep 1, 2025
Why is there extra propeller noise from my Horizon Hobby E-flite Night Timber X?
- J
  Jared RodgersSep 1, 2025
  Excessive propeller noise or vibration in your Horizon Hobby Toy can be due to a damaged propeller, spinner, collet, or motor; replace any damaged parts. If the propeller is unbalanced, balance or replace it. Also, ensure the prop nut is tightened.
J
Joshua AlexanderSep 5, 2025
Why does my Horizon Hobby Toy have inconsistent flight performance?
- J
  Joseph ChambersSep 5, 2025
  Inconsistent flight performance in your Horizon Hobby Toy may be due to several reasons. If the trim is not at neutral and you adjust trim more than 8 clicks, adjust the clevis to remove trim. Ensure no Sub-Trim is used, and adjust the servo linkage instead. Also, make sure the aircraft remains immobile for 5 seconds after connecting the battery, with the throttle stick in the lowest position.
M
Michael GrahamSep 9, 2025
What to do if Horizon Hobby Toy has incorrect response to AS3X Control Direction Test?
- J
  John Gardner IVSep 9, 2025
  If your Horizon Hobby Toy shows an incorrect response to the AS3X Control Direction Test, it indicates incorrect direction settings in the receiver, which can lead to a crash. Do not fly the aircraft. Correct the direction settings by referring to the receiver manual before attempting to fly.

Horizon Hobby E-flite Night Timber X Specifications

General

Flaps	Yes
Motor	Brushless Outrunner
Battery	3S-4S 2200mAh LiPo
LED Lighting System	Yes
Recommended Experience Level	Intermediate

Summary

Safety Precautions and Warnings

General Safety Precautions

Essential safety rules to follow when operating the model aircraft to prevent injury or damage.

Warning Against Counterfeit Products

Advisory against using counterfeit replacement parts for Spektrum receivers.

Box Contents

Transmitter Setup Chart

Chart detailing transmitter setup parameters for dual rates and servo travel.

Dual Rates and Expo Settings

Guidance on setting dual rates and expo for optimal flight control.

Center of Gravity (CG)

Information on locating the correct center of gravity for the aircraft.

Flight Timer Setting

Recommendation for setting the flight timer on the transmitter.

Specifications

SAFE® Select Technology

SAFE Select Overview

Explanation of SAFE Select technology for flight envelope protection and self-leveling.

Preflight Steps

A checklist of essential steps to perform before the first flight.

Transmitter Setup

Dual Rates and Expo Adjustments

Instructions for adjusting dual rates and expo for flight control.

Computerized Transmitter Setup

Detailed transmitter programming steps for various Spektrum models.

Model Assembly

Landing Gear Installation

Step-by-step guide for installing the aircraft's landing gear.

Spring Assemblies Installation

Instructions for mounting the spring assemblies to the fuselage.

Model Assembly Continued

Stabilizer Joiner Options

Explanation of the two stabilizer joiners and their effect on CG.

Horizontal Tail Installation

Procedure for installing the horizontal stabilizer and LED connectors.

Pushrod Keeper Installation

Guide for installing the pushrod keeper onto the control horn.

Model Assembly Continued

Propeller Installation

Step-by-step instructions for installing the propeller and spinner.

Wing Assembly and Connections

Guide for assembling the wings and connecting servos and lights.

Battery Installation and ESC Arming

Battery Selection and Installation

Recommendations for battery selection and proper installation.

ESC Arming Procedure

Steps to safely arm the Electronic Speed Controller (ESC) before flight.

Center of Gravity (CG)

Binding Procedures

General Binding Tips

Helpful advice and tips for a successful radio system binding process.

SAFE Select Binding

Instructions for binding the aircraft with SAFE Select enabled or disabled.

Binding Methods

Details on using the bind button or bind plug for the binding process.

SAFE® Select Switch Designation

Assigning a Switch to SAFE Select

Procedure for assigning a transmitter switch to control SAFE Select modes.

Switch Assignment Stick Positions

Visual guide for stick positions when assigning a switch.

SMART Technology™ Telemetry

Viewing Telemetry Data

Steps to access and view telemetry data from the ESC and receiver.

Control Horn and Servo Arm Settings

Factory Settings and Tuning

Guide to factory settings for control horns and servo arms, with tuning options.

Control Surface Centering

Control Direction Test

Elevator and Rudder Direction

Checking elevator and rudder control surface response to transmitter commands.

Aileron and Flaps Direction

Verifying aileron and flap control surface movement.

AS3X Control Direction Test

AS3X Control Direction Test Procedure

Procedure to ensure the AS3X control system is functioning correctly.

In Flight Trimming

Flight Trimming Procedure

Steps for trimming the aircraft for level flight during its first flight.

Flying Tips and Repairs

Radio System Range Check

Importance of performing a radio system range check before flying.

Oscillation Troubleshooting

Guidance on identifying and resolving control surface oscillation.

Takeoff Procedure

Instructions for performing a successful takeoff from land or water.

Flying and Landing Procedures

Guidance on maintaining control during flight and executing safe landings.

Water Operations

Tips for taking off and landing on water using optional floats.

Low Voltage Cutoff (LVC)

Explanation of the ESC's Low Voltage Cutoff feature and battery care.

Foam Repairs

Information on repairing EPO foam components using adhesives.

SAFE Select Flying

SAFE Select Flight Operation

How to utilize SAFE Select for enhanced flight stability and control.

PNP Receiver Installation

Receiver Mounting and Connections

Steps for installing and connecting the Spektrum AR637TA receiver.

Post Flight Procedures

Motor Service

Motor Disassembly and Assembly

Detailed instructions for disassembling and reassembling the motor.

AS3X Troubleshooting

AS3X Oscillation and Performance Issues

Troubleshooting common oscillation and performance problems with AS3X.

Incorrect AS3X Control Response

Resolving issues related to incorrect control surface reactions in AS3X mode.

General Troubleshooting Guide

Aircraft Response and Control Problems

Diagnosing and fixing issues with aircraft response and control surfaces.

Binding and Connection Issues

Solutions for problems encountered during binding or transmitter connection.

Power and Propeller Issues

Addressing issues related to motor power, propellers, and battery life.

Optional Installations

Slat Installation

Instructions for installing optional slats for STOL performance.

Thrust Reversing Setup

Guide for setting up the optional thrust reversing feature.

Float Assembly

Steps for assembling the optional float set for water operations.

Float Installation

Float Set Attachment

Procedure for attaching the assembled float set to the fuselage.

BNF Advanced Receiver Setup

Servo Plug Order Change

Instructions for reconfiguring servo connections for advanced aileron control.

Receiver Port Assignments

Details on AR637TA receiver port assignments for advanced setup.

Advanced Transmitter Setup

General Advanced Setup Parameters

Key parameters for setting up advanced flight modes on transmitters.

Specific Transmitter Configuration

Configuration details for specific Spektrum transmitter models.

AMA National Model Aircraft Safety Code

General Safety Guidelines

General rules for safe model aircraft operation and conduct.

Radio Control Safety Guidelines

Specific safety rules pertaining to radio control operations.

Limited Warranty

Warranty Terms and Exclusions

Details on what the warranty covers and what is excluded.

Service and Contact Information

Information on obtaining warranty service and contacting support.

Related product manuals

E-flite Turbo Timber 1.5m

72 pages

E-FLITE Turbo Timber Evolution

22 pages

Horizon Hobby E-FLITE Ultrix

16 pages

Horizon Hobby E-flite DRACO 2.0m

23 pages

E-FLITE Viper 90mm EDF

68 pages

E-flite Habu SS 50mm EDF

24 pages

E-flite Commander mPd 1.4m

22 pages

E-FLITE Ultimate 3D BNF Basic

22 pages

E-FLITE Carbon-Z Cessna 150T 2.1m

26 pages

E-flite PLATINUM DHC-2 Beaver ARF

52 pages

Horizon Hobby E-flite Night Timber X User Manual

Table of Contents

Questions and Answers:

Horizon Hobby E-flite Night Timber X Specifications

Summary

Safety Precautions and Warnings

General Safety Precautions

Warning Against Counterfeit Products

Box Contents

Transmitter Setup Chart

Dual Rates and Expo Settings

Center of Gravity (CG)

Flight Timer Setting

Specifications

SAFE® Select Technology

SAFE Select Overview

Preflight Steps

Transmitter Setup

Dual Rates and Expo Adjustments

Computerized Transmitter Setup

Model Assembly

Landing Gear Installation

Spring Assemblies Installation

Model Assembly Continued

Stabilizer Joiner Options

Horizontal Tail Installation

Pushrod Keeper Installation

Model Assembly Continued

Propeller Installation

Wing Assembly and Connections

Battery Installation and ESC Arming

Battery Selection and Installation

ESC Arming Procedure

Center of Gravity (CG)

Binding Procedures

General Binding Tips

SAFE Select Binding

Binding Methods

SAFE® Select Switch Designation

Assigning a Switch to SAFE Select

Switch Assignment Stick Positions

SMART Technology™ Telemetry

Viewing Telemetry Data

Control Horn and Servo Arm Settings

Factory Settings and Tuning

Control Surface Centering

Control Direction Test

Elevator and Rudder Direction

Aileron and Flaps Direction

AS3X Control Direction Test

AS3X Control Direction Test Procedure

In Flight Trimming

Flight Trimming Procedure

Flying Tips and Repairs

Radio System Range Check

Oscillation Troubleshooting

Takeoff Procedure

Flying and Landing Procedures

Water Operations

Low Voltage Cutoff (LVC)

Foam Repairs

SAFE Select Flying

SAFE Select Flight Operation

PNP Receiver Installation

Receiver Mounting and Connections

Post Flight Procedures

Motor Service

Motor Disassembly and Assembly

AS3X Troubleshooting

AS3X Oscillation and Performance Issues

Incorrect AS3X Control Response

General Troubleshooting Guide

Aircraft Response and Control Problems

Binding and Connection Issues

Power and Propeller Issues

Optional Installations

Slat Installation

Thrust Reversing Setup

Float Assembly

Float Installation