To Next PageTo Next PageHow to remove white film from dishes in Hotpoint LTF 11M132?
If your Hotpoint dishwasher leaves a white film or limescale on dishes and glasses, it could be due to a lack of refined salt. Adjust the water hardness setting appropriately. Ensure the salt and rinse-aid dispenser caps are properly closed. Check if the rinse aid has run out or if the dosage is too low.
What to do if no water drain out of Hotpoint dishwasher?
If your Hotpoint dishwasher isn't draining water, it could be due to several reasons. First, ensure the wash cycle has completed. Check the water drain hose for any bends. Also, inspect the drain duct and filter for clogs from food residues. Finally, verify the drain hose height.
Why won’t my Hotpoint Dishwasher load water and it is blocked with flashing lights?
If your Hotpoint dishwasher won't load water and shows flashing lights, check if there's water in the mains supply and the tap is open. Inspect the water inlet hose for bends. Clean any clogged filters and the drain duct. After checking and cleaning, restart the dishwasher. If the issue continues, turn off the water tap, remove the plug.
Why are the dishes not clean after washing in my Hotpoint Dishwasher?
If your dishes aren't clean after a cycle in your Hotpoint dishwasher, ensure the crockery is arranged properly and the spray arms can rotate freely. Select an appropriate wash cycle. Verify you're using the correct amount and type of detergent, and that the rinse aid compartment lid is closed correctly. Check and clean the filter and spray arm holes if they're dirty or clogged. Ensure the refined salt level is adequate and the height of the dishes is compatible with the rack adjustment.
What to do if Hotpoint Dishwasher door won’t close?
If the door of your Hotpoint dishwasher won't close, make sure the racks are fully inserted. Also, ensure the lock is released by pushing the door firmly until you hear a 'clacking' noise.
Why is crockery not drying properly in my Hotpoint Dishwasher?
If your crockery isn't drying properly in your Hotpoint dishwasher, it might be because you selected a wash cycle without a drying program. Also, check if the rinse aid has been used up or the rinse aid dispenser setting isn't suitable. Note that water drops are normal on non-stick or plastic crockery.
Why are my dishes streaked after using my Hotpoint LTF 11M132?
If your Hotpoint dishwasher leaves streaks or a bluish tinge on dishes and glasses, it's likely that the rinse aid dosage is too high.
Why do dishes and glasses have a bluish tinge in my Hotpoint LTF 11M132?
If your dishes and glasses have streaks or a bluish tinge after being washed in your Hotpoint dishwasher, it might be because the rinse aid dosage is too high.
Why isn't my Hotpoint LTF 11M132 Dishwasher drying properly?
If your crockery isn't drying properly in your Hotpoint dishwasher, check if you've selected a wash cycle without a drying program. Ensure the rinse aid hasn't run out and that the rinse aid dispenser setting is appropriate. Note that non-stick or plastic crockery may naturally retain water drops.
Why are the dishes and glasses covered in a white film in my Hotpoint LTF 11M132?
If your dishes and glasses are covered in a white film or limescale deposits after washing in your Hotpoint dishwasher, ensure the dishwasher has refined salt and the water hardness setting is correct. Also, check that the salt and rinse-aid dispenser caps are properly closed, and ensure that the rinse aid hasn't run out or the dosage isn't too low.
General| Type | Freestanding |
|---|---|
| Appliance placement | Freestanding |
| Energy Efficiency Class | A++ |
| Number of Place Settings | 11 place settings |
| Noise Level | 42 dB |
| Height | 85 cm |
| Width | 60 cm |
| Depth | 60 cm |
| Weight | 40 kg |
| Annual energy consumption | 225 kWh |
| Capacity | 11 place settings |
| Delay Start | Yes |
| Half Load Option | Yes |
| Dimensions (H x W x D) | 85 x 60 x 60 cm |
| Washing programs | Eco, Intensive, Normal |
Safety guidelines for operation, children, domestic use, and electrical safety.
Tips for reducing water and energy consumption during wash cycles.
How to position and level the dishwasher correctly for stable operation.
Instructions for connecting the water inlet and outlet hoses to the appliance.
Guidelines for connecting the drain hose to a suitable drain duct.
Details about the anti-flooding system for safety and leak prevention.
Safety requirements and steps for connecting the appliance to the electrical supply.
How to set the water hardness level for optimal performance of the softener.
Explanation of buttons, indicators, and symbols on the control panel.
Step-by-step guide to starting a wash cycle.
Detailed instructions for cleaning the filter assembly for optimal performance.
Solutions for when the dishwasher fails to start or respond to controls.
Troubleshooting steps for issues with water not draining from the dishwasher.
Solutions for when dishes are not coming out clean after a wash cycle.
Steps to take if the dishwasher is not filling with water.
What to do when the appliance shows flashing lights indicating a blockage.
Details of the standard 12-month manufacturer's guarantee.
