HP 6038A Service Manual

Table 1-1. Specifications and Supplemental Characteristics {continued}
OUTPUT BOUNDARY SPECIFICATION
Voltage Current Power
Current Voltage
Power
(V) (A)
(W) lA)
(V) (W)
20 10.0
200 3.3
60 200
25
8.5 212
4.0
54 216
30 7.6 228
5.0 46
232
35
6.7
234
6.0
40 240
40 6.0
240
7.0
34 238
45 5.3
237 8.0
29 232
50 4.6
232 9.0
24 217
55
4.1 226 10.0
20 200
60 3.3 200
.200W
50
\
40
— -
—
|30
-
1
,aoow
20
-
1
1
10
-
1
1
!
2 4
6
8 iO
AMPS
Load Effect
For a load change equal to the maximum available current
rating of the supply at the set voltage (CV) or maximum
available voltage rating at the set current (CO:
Voltage: 0.01% +3 mV
Current: 0.01 % +5 mA
Source Effect
For a line change within rating:
Voltage: 0.01 % +2 mV
Current: 0.01% +2 mA
DC Output Isolation
Either output terminal may be floated up to ±240 Vdc (in¬
cluding output voltage) from earth ground.
PARD (Ripple and Noise)
RMS/pk-pk 20HZ-20 MHz:
Voltage: 3 mV/30 mV
Current; 5 mA
Common mode current: 1 mA/40 mA typical
Temperature Coefficient:
Change in output per °C after a 30-minute warmup.
Voltage: 50 ppm +3 mV
Current: 30 ppm -t-0.3 mA
Drift (Stability)
Change in output over an 8-hr interval under constant line,
load and ambient temperature after 30-minute warmup.
Voltage: 0.02% +2 mV
Current: 0.03% -f3 mA
Load Transient Recovery Time
The time required for the output voltage to recover within
a band around the nominal voltage following a 10% or 50%
change in load current.
10% load current change: 1 ms to within 75 mV
50% load current change: 2 ms to within 200 mV
Output Imepdance (Typical)
See graph:
fREOUENCY IH!
Programming Resolution
Voltage: 15 mV
Current: 2.5 mA
Programming Accuracy (25 ±5 °C)
Voltage: 0.035% -t-40 mV
Current: 0.085% -i-IOmA
Both channels are monotonic over the operating temperature
range.
Programming Response Time
Maximum time for output voltage to change from 0 to 60
V or 60 V to 2 V and settle within 15 mV of final value.
Up: Full load (18 ohms) 225 ms
Light load (400 ohms) 225 ms
No load 225 ms
Down: Full toad (18 ohms) 400 ms
Light load (400 ohms) 750 ms
No load 1500 ms
Typical programming response time data for changes other
than full-scale excursions:
full toad tight load no load
18 ohms 400 ohms
Up: 0 -
60 V 150 ms
120 ms 120 ms
0 - 30 V
120 ms 100
ms 100 ms
20 -
60 V 120 ms
100 ms 100 ms
Down: 60
- 2 V 150 ms
400 ms 850 ms
60 • - 10 V
110 ms 210 ms
350 ms
60 - - 30 V 160 ms
340 ms 500 ms

HP 6038A Specifications

General

Brand	HP
Model	6038A
Category	Inverter
Language	English