HP 8753D - Frequency Response Error-Corrections; Response Error-Correction for Reflection Measurements

Frequency Response
Error-Corrections
Y
ou
can
remove
the frequency
response of
the test
setup for
the following
measurements.
reection
measurements
transmission
measurements
combined
reection
and
transmission
measurements
Response
Error-Correction
for
Reection
Measurements
1.
Press
4
PRESET
5
.
2.
Select
the
type
of
measurement
you
want
to
make
.
If
you
want
to
make
a
reection
measurement
on
PORT
1(in
the forward
direction, S
11
),
leave
the
instrument
default
setting.
If
you
want
to
make
a
reection measurement
on PORT
2(in
the reverse
direction
S
22
),
press:
4
MEAS
5
N
N
N
N
N
N
N
N
N
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Refl:
REV
S22
(B/R)
Set
any
other
measurement
parameters
that
you
want
for
the
device
measurement:
power
,
sweep
type
,
number
of
points
,
or
IF
bandwidth.
T
o
access
the
measurement
error-correction
menus
,
press:
4
CAL
5
If
your
calibration kit
is
dierent
than
the
kit
specied
under
the
N
N
N
N
N
N
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
N
N
N
N
N
CAL
KIT
[ ]
softkey
,
press:
N
N
N
N
N
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
CAL
KIT
N
N
N
N
N
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
N
N
N
N
N
N
N
N
N
N
N
N
SELECT
CAL
KIT (select
your
type
of
kit)
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
RETURN
If
your
type
of
calibration
kit
is
not
listed
in
the
displayed
menu, refer
to the
\Modifying
Calibration
Standards"
procedure
,
located
later
in
this
chapter
.
T
o
select
a
response
correction,
press:
4
CAL
5
N
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
CALIBRATE
MENU
N
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
RESPONSE
Connect
the
short
or
open
calibration
standard to
the port
you selected
for the
test
port
(PORT 1
for S
11
or PORT
2 for
S
22
).
Note
Include any adapters or cables that you will have in the device measurement.
That is
, connect the
standard device to the particular connector where you will
connect your device under test.
5-8 Optimizing Measurement Results